Welcome to program SCHED. Version: 6.02 July 2005 The manual is at http://www.aoc.nrao.edu/~cwalker/sched/sched/sched.html Unix users should set $SCHED to the base area where SCHED is installed. Most run time messages will be in sched.runlog Some useful commands to give now if running interactively: SCHedule= : Specify input file. PLOT : Invokes uv, xy, rd, and uptime plotting. FREQLIST=lowF,highF : Make frequency list (MHz). Then exit. EXIT : Leave program. / : End of inputs - run program (or EXIT). SRREAD: Reading source catalog: Program_input RDSET: Reading setup file: 4cmgd.set STREAD: Reading station catalog: /home/filehost/cwalker/sched/catalogs/stations.dat STREAD: Will read locations file /home/filehost/cwalker/sched/catalogs/locations.dat SCHIN: Found 443 input scans. TPINI: Using default tape initialization information. SCHIN: * Automatic tape allocation requested at: Ov Br Mk Kp La Pt Fd Nl Hn Sc Y SRREAD: Reading source catalog: /home/filehost/cwalker/sched/catalogs/sources.vlba RDSET: Reading setup file: /home/filehost/cwalker/sched/setups/v4cm-256-8-2.set RDSET: Reading setup file: /home/filehost/cwalker/sched/setups/v6cm-256-8-2.set GETFREQ: Reading frequency file: /home/filehost/cwalker/sched/catalogs/freq.dat SHORTN: WARNING - Source names longer than 8 characters used. Mark III correlators and geodetic software will have problems. SETFCAT: In setup: 4cmgd.set Station VLA1 WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band y_vx 1 3 T F T T T T T T y_vx 2 3 T F T T T T F T y_vx 3 4 T F T T T T F T y_vx 4 4 T F T T T T F T y_08639.9j 1 3 T F T T T T F T y_08639.9j 2 3 T F T T T T F T y_08639.9j 3 4 T F T T T T T T y_08639.9j 4 4 T F T T T T F T y_08460.1j 1 3 T F T T T T F T y_08460.1j 2 3 T F T T T T T T y_08460.1j 3 4 T F T T T T F T y_08460.1j 4 4 T F T T T T F T y_08439.9j 1 3 T F T T T T F T y_08439.9j 2 3 T F T T T T T T y_08439.9j 3 4 T F T T T T F T y_08439.9j 4 4 T F T T T T F T y_08410.1j 1 3 T T T T T T T T y_08410.1j 2 3 T T T T T T F T y_08410.1j 3 4 T F T T T T F T y_08410.1j 4 4 T F T T T T F T --------------------------------------- SCHOPT: First output scan will be number 1 WRTMSG: Special message from routine SETTPS: Tape is being kept running through short gaps between scans. Add TPSTART to the SUMITEM list to see details. MINPAUSE and PRESTART may be used to adjust. Remember MINPAUSE is multiplied by the speed up factor. WRTMSG: Special message from routine AUTODOWN: * Stations using automatic tape allocation or disk recording systems are being removed from scans when the source is below the antenna pointing limits. This behavior can be overridden using DODOWN. SCHOPT: There will be 443 output scans ( 1 - 443) from 20/13:30:00 to 21/01:28:57 SUMOPE: Writing summary file bd109c.sum OMSOUT: Writing OMS file bd109c.oms FLAGS: Writing apriori flagging file bd109c.flag Processing VLBA_OV Processing VLBA_BR Processing VLBA_MK Processing VLBA_KP Processing VLBA_LA Processing VLBA_PT Processing VLBA_FD Processing VLBA_NL Processing VLBA_HN Processing VLBA_SC Processing VLA1