Welcome to program SCHED.  Version: Release of 18 Sept. 2003

The manual is at http://www.aoc.nrao.edu/~cwalker/sched/sched/sched.html
Unix users should set $SCHED to the base area where SCHED is installed.
** NEW ** Most run time messages will be in sched.runlog

Some useful commands to give now if running interactively:
   SCHedule=<filename>    :  Specify input file.
   PLOT                   :  Invokes uv, xy, rd, and uptime plotting.
   FREQLIST=lowF,highF    :  Make frequency list (MHz).  Then exit.
   EXIT                   :  Leave program.
   /                      :  End of inputs - run program (or EXIT).

SRREAD:  Reading source catalog: Program_input
SRREAD:  Please convert source catalog from use of EPOCH to EQUINOX.
RDSET:   Reading setup file: v90cm.set
SCHIN:  DOSTA specified as VL
        Some stations may be skipped.
STREAD:  Reading station catalog: /home/filehost/cwalker/sched/catalogs/stations.dat
STREAD:  Will read locations file /home/filehost/cwalker/sched/catalogs/locations.dat
SCHIN:   Found    30 input scans.
SCHIN:   * Automatic tape allocation requested at: Sc Hn Nl Fd La Pt Kp Ov Br Mk Y
TPINI:   Using default tape initialization information.
SRREAD:  Reading source catalog: /home/filehost/cwalker/sched/catalogs/sources.vlba
GETFREQ: Reading frequency file: /home/filehost/cwalker/sched/catalogs/freq.dat
SHORTN: WARNING - Source names longer than 8 characters used.
        Mark III correlators and geodetic software will have problems.
SETFCAT: In setup: v90cm.set
         Station VLA1

WRTMSG: Special message from routine SETFCAT:

                    -----------  WARNING  -----------
SCHED could not find a frequency catalog group that matched the setup file
and station mentioned above.  Below are the closest matches with at least
some overlap in RF frequency.  You can use FREQLIST (a main program input)
to get the frequency catalog group and IF numbers that are available.  Or
you can look in freq.dat in the catalogs area.

Since SCHED cannot confirm the validity of your setup, check and be very
sure it is correct!

In the table below, a match is indicated by a T.  A mismatch is indicated by F.

   FreqCat        Baseband FreqCat  IF   First  Pol   RF    VLA   FE    RF    RF
    Group         Channel    IF    Name   LO        Chan 1   IF       Freq   Band

   y_vp               1       1      T     F     T     T     T     T     F     T
   y_vp               2       3      T     F     T     T     T     T     F     T
   y_vp               3       1      T     F     T     T     T     T     F     T
   y_vp               4       3      T     F     T     T     T     T     F     T
   y_vp               5       2      T     T     T     T     T     T     T     T
   y_vp               6       4      T     T     T     T     T     T     T     T
   y_vp               7       2      T     T     T     T     T     T     T     T
   y_vp               8       4      T     T     T     T     T     T     T     T

---------------------------------------

SCHOPT:  First output scan will be number     1

WRTMSG: Special message from routine AUTODOWN:

  * Stations using automatic tape allocation are being removed
    from scans when the source is below the antenna pointing limits.

SCHOPT:  There will be    30 output scans (    1 -    30) from  30/06:00:00 to  30/15:44:00
SUMOPE:  Writing summary file bc138c.sum
OMSOUT:  Writing OMS file bc138c.oms
FLAGS:   Writing apriori flagging file bc138c.flag
 Processing VLBA_SC
 Processing VLBA_HN
 Processing VLBA_NL
 Processing VLBA_FD
 Processing VLBA_LA
 Processing VLBA_PT
 Processing VLBA_KP
 Processing VLBA_OV
 Processing VLBA_BR
 Processing VLBA_MK
 Processing VLA1