SUMMARY FILE FOR PROJECT: MT707 COVER INFORMATION: Experiment: VLBA Monitoring Exp. Code: MT707 Start Day 53 is Thu 22 Feb 2007 MJD 54153 Schedule Version: 3.10 Processed by SCHED version: 6.05 June 2006 PI: Lorant Sjouwerman Address: NRAO-AOC P.O.Box O Socorro NM 87801, U.S.A. Phone: +1-505-838-4507 (home) EMAIL: lsjouwer@nrao.edu, analysts@nrao.edu Fax: Phone during observation: +1-505-835-7332 (work) Observing mode: VLBA 128MHz 8bbc 1bit R+L Notes: VLBA Monitoring test in dynamic scheduling and runs for 90 minutes (1.5 hours) total. Note: MAKE SURE ONE SOURCE IS SELECTED COVER LETTER: Please schedule ONE source depending on between approximately -3h to +3h of LST in Pie Town; a source can be selected by deleting the -one and only- ONE explanation mark in front of it. CORRELATION REQUESTS (Defaults in parentheses): Correlator (Required if recording): SOCORRO Correlator average time (2 sec): 1.835 sec. Alternate average time (for spacecraft). 0.000 sec. Spectral channels per baseband (16): 64 Number of antennas to be correlated: 10 Polarization (ON): ON Correlator weighting function (UNIFORM): UNIFORM Distribution tape (DAT): DAT Source positions from: SCHEDULE Shipping address for correlator output: Analysts Office NRAO-AOC P.O.Box O, Socorro NM 87801, U.S.A. Correlator Notes: Note: Job scripts will produce three different setups. VLBA auto-release test. Please correlate at highest priority. Please run sniffer promptly after correlation and directly after that get the data tape to the analysts (AOC mail box). ThanX.. DERIVED INFORMATION FOR CORRELATION: Elapsed time for project: 1.50 hours. Total time in scheduled scans: 1.21 hours. Total time in recording scans: 1.21 hours. Total number of baseline hours: 66.73 (Recording scans only) Projected maximum data output rate from the correlator: 245.5 kbytes/sec if processed in one pass. Projected correlator output data set size: 1024.8 Mbytes NOTE: Above numbers assume the same correlator parameters are used for all data. STATIONS USED IN SCHEDULE: Station Code Latitude Longitude Elevation X Y Z VLBA_PT Pt 34.30102 108.11919 2365. -1640953.712 -5014816.024 3575411.880 VLBA_KP Kp 31.95630 111.61242 1902. -1995678.626 -5037317.713 3357328.129 VLBA_LA La 35.77512 106.24560 1962. -1449752.359 -4975298.588 3709123.928 VLBA_SC Sc 17.75658 64.58363 -15. 2607848.521 -5488069.685 1932739.540 VLBA_FD Fd 30.63503 103.94482 1606. -1324009.127 -5332181.966 3231962.474 VLBA_HN Hn 42.93361 71.98658 296. 1446375.116 -4447939.656 4322306.124 VLBA_NL Nl 41.77142 91.57414 222. -130872.254 -4762317.116 4226851.040 VLBA_BR Br 48.13122 119.68328 251. -2112064.976 -3705356.516 4726813.798 VLBA_OV Ov 37.23165 118.27705 1196. -2409150.112 -4478573.229 3838617.399 VLBA_MK Mk 19.80138 155.45550 3763. -5464074.960 -2495249.116 2148296.844 Plate tectonic motion adjustments for MJD 54153 Station Code Station motions (m/yr) Adjusted positions X Y Z MJD0 X Y Z VLBA_PT Pt -0.0138 -0.0003 -0.0082 50449 -1640953.852 -5014816.027 3575411.797 VLBA_KP Kp -0.0127 0.0006 -0.0081 50449 -1995678.755 -5037317.707 3357328.047 VLBA_LA La -0.0132 0.0008 -0.0068 50449 -1449752.493 -4975298.580 3709123.859 VLBA_SC Sc 0.0082 0.0098 0.0100 50449 2607848.605 -5488069.585 1932739.642 VLBA_FD Fd -0.0116 0.0004 -0.0066 50449 -1324009.244 -5332181.962 3231962.407 VLBA_HN Hn -0.0145 -0.0009 0.0019 50449 1446374.969 -4447939.665 4322306.144 VLBA_NL Nl -0.0144 0.0013 -0.0039 50449 -130872.400 -4762317.103 4226851.001 VLBA_BR Br -0.0136 0.0008 -0.0095 50449 -2112065.114 -3705356.507 4726813.702 VLBA_OV Ov -0.0175 0.0068 -0.0054 50449 -2409150.290 -4478573.160 3838617.344 VLBA_MK Mk -0.0137 0.0622 0.0303 50449 -5464075.099 -2495248.485 2148297.151 BASELINE LENGTHS (km) Pt Kp La Sc Fd Hn Nl Br Ov Mk Pt 0 417 236 4579 564 3226 1663 1806 973 4795 Kp 417 0 652 4839 744 3623 2075 1913 845 4466 La 236 652 0 4458 608 3006 1432 1757 1088 4970 Sc 4579 4839 4458 0 4143 2853 3645 5767 5460 8611 Fd 564 744 608 4143 0 3105 1654 2345 1508 5134 Hn 3226 3623 3006 2853 3105 0 1611 3657 3885 7502 Nl 1663 2075 1432 3645 1654 1611 0 2300 2328 6156 Br 1806 1913 1757 5767 2345 3657 2300 0 1214 4398 Ov 973 845 1088 5460 1508 3885 2328 1214 0 4015 Mk 4795 4466 4970 8611 5134 7502 6156 4398 4015 0 RECORDING SYSTEM INFORMATION: DISKS - Stations potentially recording on disks. Station Drive type DAR VLBA_PT MARK5A VLBA VLBA_KP MARK5A VLBA VLBA_LA MARK5A VLBA VLBA_SC MARK5A VLBA VLBA_FD MARK5A VLBA VLBA_HN MARK5A VLBA VLBA_NL MARK5A VLBA VLBA_BR MARK5A VLBA VLBA_OV MARK5A VLBA VLBA_MK MARK5A VLBA EXPERIMENT SUMMARY: Number of input scans: 11 Number of scans scheduled: 11 Number of stations: 10 Number of sources input: 1 Number of setup files used: 11 Station summaries (tape stations): Station Control Scans Scan Tape Tapes Passes Readbacks Formatter Sync Hours Hours Reconfigures Hours Station summaries (disk stations): Station Control Scans Scan Hours Record hrs Gbytes Formatter Sync Reconfigures Hours VLBA_PT VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_KP VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_LA VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_SC VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_FD VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_HN VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_NL VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_BR VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_OV VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_MK VLBA 11 1.21 1.21 70. 4/ 0 0.06 Notes on the station summaries: "Sync Hours" is on-source, in-scan time lost during correlation to resyncing recordings. Resyncs follow tape stoppages and formatter reconfigures. For VLBA DAR stations, total reconfigures and reconfigures during recording are shown. Reconfigures during recording can cause slow correlator sync. Any reconfigure can slow sync at JIVE. The following setup groups are the same as group 1 below. 2:VLBA_KP 3:VLBA_LA 4:VLBA_SC 5:VLBA_FD 6:VLBA_HN 7:VLBA_NL 8:VLBA_BR 9:VLBA_OV 10:VLBA_MK Setup file: band.21cm Matches group v20cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 1 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 1 Setup file default. Used pcal sets: 1 LO sum= 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 BBC fr= 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 11 below. 12:VLBA_KP 13:VLBA_LA 14:VLBA_SC 15:VLBA_FD 16:VLBA_HN 17:VLBA_NL 18:VLBA_BR 19:VLBA_OV 20:VLBA_MK Setup file: band.18cm Matches group v20cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 11 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 11 Setup file default. Used pcal sets: 1 LO sum= 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 BBC fr= 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 21 below. 22:VLBA_KP 23:VLBA_LA 24:VLBA_SC 25:VLBA_FD 26:VLBA_HN 27:VLBA_NL 28:VLBA_BR 29:VLBA_OV 30:VLBA_MK Setup file: band.13cm Matches group v13cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 21 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 21 Setup file default. Used pcal sets: 1 LO sum= 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 BBC fr= 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 31 below. 32:VLBA_KP 33:VLBA_LA 34:VLBA_SC 35:VLBA_FD 36:VLBA_HN 37:VLBA_NL 38:VLBA_BR 39:VLBA_OV 40:VLBA_MK Setup file: band.6cm Matches group v6cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 31 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 31 Setup file default. Used pcal sets: 1 LO sum= 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 BBC fr= 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 41 below. 42:VLBA_KP 43:VLBA_LA 44:VLBA_SC 45:VLBA_FD 46:VLBA_HN 47:VLBA_NL 48:VLBA_BR 49:VLBA_OV 50:VLBA_MK Setup file: band.4cm Matches group v4cm_3 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 41 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 41 Setup file default. Used pcal sets: 1 LO sum= 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 BBC fr= 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 51 below. 52:VLBA_KP 53:VLBA_LA 54:VLBA_SC 55:VLBA_FD 56:VLBA_HN 57:VLBA_NL 58:VLBA_BR 59:VLBA_OV 60:VLBA_MK Setup file: band.2cm Matches group v2cm_d3 in /home/arana/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 51 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 51 Setup file default. Used pcal sets: 1 LO sum= 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 BBC fr= 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 61 below. 62:VLBA_KP 63:VLBA_LA 64:VLBA_SC 65:VLBA_FD 66:VLBA_HN 67:VLBA_NL 68:VLBA_BR 69:VLBA_OV 70:VLBA_MK Setup file: band.1cm Matches group v1cm_b3 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 61 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 1cm omit 1cm VLBA Synth= 9.1 15.4 12.4 The following frequency sets based on this setup were used. Frequency Set: 61 Setup file default. Used pcal sets: 1 LO sum= 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 71 below. 72:VLBA_KP 73:VLBA_LA 74:VLBA_SC 75:VLBA_FD 76:VLBA_HN 77:VLBA_NL 78:VLBA_BR 79:VLBA_OV 80:VLBA_MK Setup file: band.7mm Matches group v7mm_c8 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 71 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 7mm omit 7mm omit VLBA Synth= 15.4 7.6 11.6 The following frequency sets based on this setup were used. Frequency Set: 71 Setup file default. Used pcal sets: 1 LO sum= 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 81 below. 82:VLBA_KP 83:VLBA_LA 84:VLBA_SC 85:VLBA_FD 86:VLBA_HN 87:VLBA_NL 88:VLBA_BR 89:VLBA_OV 90:VLBA_MK Setup file: band.6-16 Matches group v6cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 81 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 4 Speedup factor: 1.00 Disk used to record data. 1st LO= 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U Pol. = RCP LCP RCP LCP BBC = 1 2 3 4 BBC SB= U U U U IF = A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 81 Setup file default. Used pcal sets: 2 LO sum= 4974.49 4974.49 4990.49 4990.49 BBC fr= 874.49 874.49 890.49 890.49 Bandwd= 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 2 PCAL = 1MHZ PCALXB1= S1 S3 S1 S3 S1 S3 S1 S3 PCALXB2= S2 S4 S2 S4 S2 S4 S2 S4 PCALFR1= 510 510 13510 13510 0 0 1510 1510 PCALFR2= 510 510 13510 13510 0 0 1510 1510 Track assignments are: track1= 2, 10, 18, 26 barrel=roll_off The following setup groups are the same as group 91 below. 92:VLBA_KP 93:VLBA_LA 94:VLBA_SC 95:VLBA_FD 96:VLBA_HN 97:VLBA_NL 98:VLBA_BR 99:VLBA_OV 100:VLBA_MK Setup file: band.6-4 Matches group v6cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 91 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 91 Setup file default. Used pcal sets: 3 LO sum= 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 BBC fr= 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 3 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 2510 2510 2510 2510 PCALFR2= 510 510 510 510 2510 2510 2510 2510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 101 below. 102:VLBA_KP 103:VLBA_LA 104:VLBA_SC 105:VLBA_FD 106:VLBA_HN 107:VLBA_NL 108:VLBA_BR 109:VLBA_OV 110:VLBA_MK Setup file: band.9050 Matches group v5090n in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 101 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 101 Setup file default. Used pcal sets: 4 LO sum= 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 BBC fr= 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 4 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 10 10 10 10 3010 3010 3010 3010 PCALFR2= 10 10 10 10 3010 3010 3010 3010 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off SUMMARY for experiment MT707 VLBA Monitoring Top item is: Seconds antenna is on source during scan. Bottom item is: Slew time in seconds from previous source. TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 53 is Thu 22 Feb 2007 MJD 54153 SCAN DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Pt Kp La Sc Fd Hn Nl Br Ov Mk 1 53 14:43:58 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 14:50:27 band.21cm - 0 0 0 0 0 0 0 0 0 0 2 53 14:52:27 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 14:58:56 band.18cm - 7 7 6 7 7 6 6 6 6 7 3 53 14:59:56 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 15:06:24 band.13cm - 6 6 6 6 6 6 5 5 6 6 4 53 15:08:24 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 15:14:53 band.6cm - 6 7 6 7 7 6 6 6 6 7 5 53 15:15:53 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 15:22:22 band.4cm - 6 6 6 6 6 6 5 5 6 6 6 53 15:24:22 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 15:30:50 band.2cm - 6 7 6 7 6 6 6 6 6 7 7 53 15:31:50 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 15:38:19 band.1cm - 6 6 6 6 6 6 5 5 6 6 8 53 15:40:19 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 15:46:48 band.7mm - 6 7 6 7 6 6 6 6 6 7 9 53 15:48:48 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 15:55:16 band.6-16 - 6 6 6 7 6 6 6 6 6 7 10 53 15:56:16 1749+096 - 389 389 389 389 389 389 389 389 389 389 53 16:02:45 band.6-4 - 6 6 6 6 6 6 6 5 6 6 11 53 16:05:45 1749+096 - 479 479 479 479 479 479 479 479 479 479 53 16:13:43 band.9050 - 7 7 7 7 7 7 7 7 7 7 SUMMARY for experiment MT707 VLBA Monitoring Top item is: Seconds antenna is on source before scan start. Bottom item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 53 is Thu 22 Feb 2007 MJD 54153 SCAN DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Pt Kp La Sc Fd Hn Nl Br Ov Mk 1 53 14:43:58 1749+096 - 0 0 0 0 0 0 0 0 0 0 53 14:50:27 band.21cm - 65 67 64 50 69 46 56 50 60 40 2 53 14:52:27 1749+096 - 113 113 113 113 113 114 114 114 113 113 53 14:58:56 band.18cm - 65 67 64 48 69 45 55 50 61 42 3 53 14:59:56 1749+096 - 54 54 54 54 54 54 54 54 54 54 53 15:06:24 band.13cm - 65 68 64 46 68 44 54 51 61 44 4 53 15:08:24 1749+096 - 113 113 113 113 113 113 114 114 113 113 53 15:14:53 band.6cm - 65 68 63 44 68 42 53 51 62 46 5 53 15:15:53 1749+096 - 54 54 54 54 54 54 54 54 54 54 53 15:22:22 band.4cm - 65 68 63 42 67 41 53 51 62 48 6 53 15:24:22 1749+096 - 113 113 113 113 113 113 114 114 113 113 53 15:30:50 band.2cm - 64 67 63 40 67 40 52 51 62 50 7 53 15:31:50 1749+096 - 54 54 54 54 54 54 54 54 54 54 53 15:38:19 band.1cm - 64 67 62 38 66 39 51 51 62 52 8 53 15:40:19 1749+096 - 113 113 113 113 113 113 114 114 113 113 53 15:46:48 band.7mm - 63 67 61 36 65 37 50 52 62 54 9 53 15:48:48 1749+096 - 113 113 113 113 113 113 114 114 113 113 53 15:55:16 band.6-16 - 63 66 60 34 63 36 49 51 62 56 10 53 15:56:16 1749+096 - 54 54 54 54 54 54 54 54 54 54 53 16:02:45 band.6-4 - 62 65 60 33 62 34 47 51 62 57 11 53 16:05:45 1749+096 - 173 173 173 172 173 173 173 173 173 172 53 16:13:43 band.9050 - 61 64 58 30 61 33 46 51 62 59 Automatic tape allocation requested for sites using VLBA control files and having 2 or more drives. SCHED cannot predict tape changes. Number of tapes or GBytes used at each autoaloc station: Includes all disk stations. Station Tapes GBytes VLBA_PT 70.4 VLBA_KP 70.4 VLBA_LA 70.4 VLBA_SC 70.4 VLBA_FD 70.4 VLBA_HN 70.4 VLBA_NL 70.4 VLBA_BR 70.4 VLBA_OV 70.4 VLBA_MK 70.4 ESTIMATED TAPE TIMES (With autoallocation): Times are approximate and assume project starts at the beginning of a tape. Times can be affected by actual tape length. Tape change may occur during scan preceeding indicated time. Tape start time. Tape end time. Station Day Time Day Time (UT) (UT) VLBA_PT 53 14:43:58 53 16:13:43 VLBA_KP 53 14:43:58 53 16:13:43 VLBA_LA 53 14:43:58 53 16:13:43 VLBA_SC 53 14:43:58 53 16:13:43 VLBA_FD 53 14:43:58 53 16:13:43 VLBA_HN 53 14:43:58 53 16:13:43 VLBA_NL 53 14:43:58 53 16:13:43 VLBA_BR 53 14:43:58 53 16:13:43 VLBA_OV 53 14:43:58 53 16:13:43 VLBA_MK 53 14:43:58 53 16:13:43 SOURCE LIST -- VLBA Monitoring Catalog positions marked with *. Precession of date coordinates is based on stop time of first scan. Names used in schedule marked with *. Short names used in VLA and SNAP files marked with +. Observation date used in B1950/J2000 coordinate conversion (PRECDATE): 1979.900 No adjustments are made for rates (DRA, DDEC). Scan hours are for recording scans only. Baseline hours are only counted for scans above horizon at both ends. Source Source position (RA/Dec) Error (B1950) (J2000) (Date) (mas) J1751+0939 17 49 10.387930 * 17 51 32.818573 17 51 52.838161 0.30 * 1749+096 09 39 42.82591 * 09 39 00.72846 09 38 36.13476 0.20 J1751+09 /home/arana/cwalker/sched/catalogs/sources.vlba VLBA Calib Survey - GSFC sols. - created L.Petrov 2005f_astro 1.213 scan hours, 54.601 baseline hours above horizon. The solar corona can cause unstable phases for sources too close to the Sun. SCHED provides warnings at individual scans for distances less than 10 degrees. The distance from the Sun to each source in this schedule is: Source Sun distance (deg) 1749+096 70.1 Barry Clark estimates from predictions by Ketan Desai of IPM scattering sizes that the Sun will cause amplitude reductions on the longest VLBA baselines at a solar distance of 60deg F^(-0.6) where F is in GHz. For common VLBI bands, this is: 327 MHz 117. deg 610 MHz 81. deg 1.6 GHz 45. deg 2.3 GHz 36. deg 5.0 GHz 23. deg 8.4 GHz 17. deg 15.0 GHz 12. deg 22.0 GHz 9. deg 43.0 GHz 6. deg J2000 coordinates formatted for possible transfer to the correlator data base: name = '1749+096' ra = 17h51m32.818573s dec = 09d39'00.72846" Catalogs: Station: /home/arana/cwalker/sched/catalogs/stations.dat Version: 2006Dec04-17:14:51 Location: /home/arana/cwalker/sched/catalogs/locations.dat Version: Not known Frequency: /home/arana/cwalker/sched/catalogs/freq.dat Version: 2006Jun08-14:55:16 Source: /home/arana/cwalker/sched/catalogs/sources.vlba Version: Not given Code versions: Release version: 6.05 June 2006 Version of VEX standard: 1.50 Version of VEX code: 0.86 Version of plot code: 1.06 Version of ephemeris code: 1.01 Version of PGPLOT: v5.2.0