SUMMARY FILE FOR PROJECT: MT606 COVER INFORMATION: Experiment: VLBA Monitoring Exp. Code: MT606 Start Day 42 is Sat 11 Feb 2006 MJD 53777 Schedule Version: 3.10 Processed by SCHED version: 6.02 July 2005 PI: Lorant Sjouwerman Address: NRAO-AOC P.O.Box O Socorro NM 87801, U.S.A. Phone: +1-505-838-4507 (home) EMAIL: lsjouwer@nrao.edu, analysts@nrao.edu Fax: Phone during observation: +1-505-835-7332 (work) Observing mode: VLBA 128MHz 8bbc 1bit R+L Notes: VLBA Monitoring test in dynamic scheduling and runs for 90 minutes (1.5 hours) total. Note: MAKE SURE ONE SOURCE IS SELECTED COVER LETTER: Please schedule ONE source depending on between approximately -3h to +3h of LST in Pie Town; a source can be selected by deleting the -one and only- ONE explanation mark in front of it. CORRELATION REQUESTS (Defaults in parentheses): Correlator (Required if recording): SOCORRO Correlator average time (2 sec): 1.835 sec. Alternate average time (for spacecraft). 0.000 sec. Spectral channels per baseband (16): 64 Number of antennas to be correlated: 10 Polarization (ON): ON Correlator weighting function (UNIFORM): UNIFORM Distribution tape (DAT): DAT Source positions from: SCHEDULE Shipping address for correlator output: Analysts Office NRAO-AOC P.O.Box O, Socorro NM 87801, U.S.A. Correlator Notes: Note: Job scripts will produce three different setups. VLBA auto-release test. Please correlate at highest priority. Please run sniffer promptly after correlation and directly after that get the data tape to the analysts (AOC mail box). ThanX.. DERIVED INFORMATION FOR CORRELATION: Elapsed time for project: 1.50 hours. Total time in scheduled scans: 1.21 hours. Total time in recording scans: 1.21 hours. Total number of baseline hours: 66.73 (Recording scans only) Projected maximum data output rate from the correlator: 245.5 kbytes/sec if processed in one pass. Projected correlator output data set size: 1024.8 Mbytes NOTE: Above numbers assume the same correlator parameters are used for all data. STATIONS USED IN SCHEDULE: Station Code Latitude Longitude Elevation X Y Z VLBA_PT Pt 34.30102 108.11919 2365. -1640953.71 -5014816.02 3575411.88 VLBA_KP Kp 31.95630 111.61242 1902. -1995678.63 -5037317.71 3357328.13 VLBA_LA La 35.77512 106.24560 1962. -1449752.36 -4975298.59 3709123.93 VLBA_SC Sc 17.75658 64.58363 -15. 2607848.52 -5488069.69 1932739.54 VLBA_FD Fd 30.63503 103.94482 1606. -1324009.13 -5332181.96 3231962.47 VLBA_HN Hn 42.93361 71.98658 296. 1446375.12 -4447939.65 4322306.12 VLBA_NL Nl 41.77142 91.57414 222. -130872.25 -4762317.11 4226851.04 VLBA_BR Br 48.13122 119.68328 251. -2112064.98 -3705356.52 4726813.80 VLBA_OV Ov 37.23165 118.27705 1196. -2409150.11 -4478573.23 3838617.40 VLBA_MK Mk 19.80138 155.45550 3763. -5464074.96 -2495249.12 2148296.84 BASELINE LENGTHS (km) Pt Kp La Sc Fd Hn Nl Br Ov Mk Pt 0 417 236 4579 564 3226 1663 1806 973 4795 Kp 417 0 652 4839 744 3623 2075 1913 845 4466 La 236 652 0 4458 608 3006 1432 1757 1088 4970 Sc 4579 4839 4458 0 4143 2853 3645 5767 5460 8611 Fd 564 744 608 4143 0 3105 1654 2345 1508 5134 Hn 3226 3623 3006 2853 3105 0 1611 3657 3885 7502 Nl 1663 2075 1432 3645 1654 1611 0 2300 2328 6156 Br 1806 1913 1757 5767 2345 3657 2300 0 1214 4398 Ov 973 845 1088 5460 1508 3885 2328 1214 0 4015 Mk 4795 4466 4970 8611 5134 7502 6156 4398 4015 0 RECORDING SYSTEM INFORMATION: Some stations may be scheduled for both tape and disk. TAPES - Stations potentially recording on tape. (See setup details later for times per pass.) Station Drives Head pos Tape len Density Start position Auto Auto Recorder DAR (ft) Driv Head indx Aloc Reverse VLBA_PT 2 14 17600 High 1 1 Yes Yes VLBA VLBA VLBA_SC 2 14 17600 High 1 1 Yes Yes VLBA VLBA VLBA_NL 2 14 17600 High 1 1 Yes Yes VLBA VLBA VLBA_OV 2 14 17600 High 1 1 Yes Yes VLBA VLBA VLBA_MK 2 14 17600 High 1 1 Yes Yes VLBA VLBA DISKS - Stations potentially recording on disks. Station Drive type VLBA_KP MARK5A VLBA_LA MARK5A VLBA_FD MARK5A VLBA_HN MARK5A VLBA_BR MARK5A EXPERIMENT SUMMARY: Number of input scans: 11 Number of scans scheduled: 11 Number of stations: 10 Number of sources input: 1 Number of setup files used: 11 Station summaries (tape stations): Station Control Scans Scan Tape Tapes Passes Readbacks Formatter Sync Hours Hours Reconfigures Hours VLBA_PT VLBA 11 1.21 1.21 1 4 6 10/ 0 0.02 VLBA_SC VLBA 11 1.21 1.21 1 4 6 10/ 0 0.02 VLBA_NL VLBA 11 1.21 1.21 1 4 6 10/ 0 0.02 VLBA_OV VLBA 11 1.21 1.21 1 4 6 10/ 0 0.02 VLBA_MK VLBA 11 1.21 1.21 1 4 6 10/ 0 0.02 Station summaries (disk stations): Station Control Scans Scan Hours Record hrs Gbytes Formatter Sync Reconfigures Hours VLBA_KP VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_LA VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_FD VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_HN VLBA 11 1.21 1.21 70. 4/ 0 0.06 VLBA_BR VLBA 11 1.21 1.21 70. 4/ 0 0.06 Notes on the station summaries: "Sync Hours" is on-source, in-scan time lost during correlation to resyncing recordings. Resyncs follow tape stoppages and formatter reconfigures. For VLBA stations, total reconfigures and reconfigures during recording are shown. Reconfigures during recording can cause slow correlator sync. Any reconfigure can slow sync at JIVE. The following setup groups are the same as group 1 below. 4:VLBA_SC 7:VLBA_NL 9:VLBA_OV 10:VLBA_MK Setup file: band.21cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 1 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 1 Setup file default. Used pcal sets: 1 LO sum= 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 BBC fr= 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 The following setup groups are the same as group 2 below. 3:VLBA_LA 5:VLBA_FD 6:VLBA_HN 8:VLBA_BR Setup file: band.21cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 2 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 2 Setup file default. Used pcal sets: 1 LO sum= 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 BBC fr= 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 11 below. 14:VLBA_SC 17:VLBA_NL 19:VLBA_OV 20:VLBA_MK Setup file: band.18cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 11 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 11 Setup file default. Used pcal sets: 1 LO sum= 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 BBC fr= 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off The following setup groups are the same as group 12 below. 13:VLBA_LA 15:VLBA_FD 16:VLBA_HN 18:VLBA_BR Setup file: band.18cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 12 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 12 Setup file default. Used pcal sets: 1 LO sum= 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 BBC fr= 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 21 below. 24:VLBA_SC 27:VLBA_NL 29:VLBA_OV 30:VLBA_MK Setup file: band.13cm Matches group v13cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 21 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 21 Setup file default. Used pcal sets: 1 LO sum= 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 BBC fr= 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 The following setup groups are the same as group 22 below. 23:VLBA_LA 25:VLBA_FD 26:VLBA_HN 28:VLBA_BR Setup file: band.13cm Matches group v13cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 22 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 22 Setup file default. Used pcal sets: 1 LO sum= 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 BBC fr= 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 31 below. 34:VLBA_SC 37:VLBA_NL 39:VLBA_OV 40:VLBA_MK Setup file: band.6cm Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 31 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 31 Setup file default. Used pcal sets: 1 LO sum= 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 BBC fr= 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 The following setup groups are the same as group 32 below. 33:VLBA_LA 35:VLBA_FD 36:VLBA_HN 38:VLBA_BR Setup file: band.6cm Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 32 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 32 Setup file default. Used pcal sets: 1 LO sum= 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 BBC fr= 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 41 below. 44:VLBA_SC 47:VLBA_NL 49:VLBA_OV 50:VLBA_MK Setup file: band.4cm Matches group v4cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 41 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 41 Setup file default. Used pcal sets: 1 LO sum= 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 BBC fr= 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off The following setup groups are the same as group 42 below. 43:VLBA_LA 45:VLBA_FD 46:VLBA_HN 48:VLBA_BR Setup file: band.4cm Matches group v4cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 42 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 42 Setup file default. Used pcal sets: 1 LO sum= 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 BBC fr= 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 51 below. 54:VLBA_SC 57:VLBA_NL 59:VLBA_OV 60:VLBA_MK Setup file: band.2cm Matches group v2cm_d3 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 51 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 51 Setup file default. Used pcal sets: 1 LO sum= 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 BBC fr= 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_auto The following setup groups are the same as group 52 below. 53:VLBA_LA 55:VLBA_FD 56:VLBA_HN 58:VLBA_BR Setup file: band.2cm Matches group v2cm_d3 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 52 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 52 Setup file default. Used pcal sets: 1 LO sum= 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 BBC fr= 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 61 below. 64:VLBA_SC 67:VLBA_NL 69:VLBA_OV 70:VLBA_MK Setup file: band.1cm Matches group v1cm_b3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 61 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 1cm omit 1cm VLBA Synth= 9.1 15.4 12.4 The following frequency sets based on this setup were used. Frequency Set: 61 Setup file default. Used pcal sets: 1 LO sum= 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 The following setup groups are the same as group 62 below. 63:VLBA_LA 65:VLBA_FD 66:VLBA_HN 68:VLBA_BR Setup file: band.1cm Matches group v1cm_b3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 62 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 1cm omit 1cm VLBA Synth= 9.1 15.4 12.4 The following frequency sets based on this setup were used. Frequency Set: 62 Setup file default. Used pcal sets: 1 LO sum= 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 71 below. 74:VLBA_SC 77:VLBA_NL 79:VLBA_OV 80:VLBA_MK Setup file: band.7mm Matches group v7mm_c8 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 71 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 7mm omit 7mm omit VLBA Synth= 15.4 7.6 11.6 The following frequency sets based on this setup were used. Frequency Set: 71 Setup file default. Used pcal sets: 1 LO sum= 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 The following setup groups are the same as group 72 below. 73:VLBA_LA 75:VLBA_FD 76:VLBA_HN 78:VLBA_BR Setup file: band.7mm Matches group v7mm_c8 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 72 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 7mm omit 7mm omit VLBA Synth= 15.4 7.6 11.6 The following frequency sets based on this setup were used. Frequency Set: 72 Setup file default. Used pcal sets: 1 LO sum= 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 81 below. 84:VLBA_SC 87:VLBA_NL 89:VLBA_OV 90:VLBA_MK Setup file: band.6-16 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 81 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 4 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U Pol. = RCP LCP RCP LCP BBC = 1 2 3 4 BBC SB= U U U U IF = A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 81 Setup file default. Used pcal sets: 2 LO sum= 4974.49 4974.49 4990.49 4990.49 BBC fr= 874.49 874.49 890.49 890.49 Bandwd= 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 2 PCAL = 1MHZ PCALXB1= S1 S3 S1 S3 S1 S3 S1 S3 PCALXB2= S2 S4 S2 S4 S2 S4 S2 S4 PCALFR1= 510 510 13510 13510 0 0 1510 1510 PCALFR2= 510 510 13510 13510 0 0 1510 1510 Track assignments are: track1= 2, 10, 18, 26 track2= 3, 11, 19, 27 barrel=roll_auto The following setup groups are the same as group 82 below. 83:VLBA_LA 85:VLBA_FD 86:VLBA_HN 88:VLBA_BR Setup file: band.6-16 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 82 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 4 Speedup factor: 1.00 Disk used to record data. 1st LO= 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U Pol. = RCP LCP RCP LCP BBC = 1 2 3 4 BBC SB= U U U U IF = A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 82 Setup file default. Used pcal sets: 2 LO sum= 4974.49 4974.49 4990.49 4990.49 BBC fr= 874.49 874.49 890.49 890.49 Bandwd= 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 2 PCAL = 1MHZ PCALXB1= S1 S3 S1 S3 S1 S3 S1 S3 PCALXB2= S2 S4 S2 S4 S2 S4 S2 S4 PCALFR1= 510 510 13510 13510 0 0 1510 1510 PCALFR2= 510 510 13510 13510 0 0 1510 1510 Track assignments are: track1= 2, 10, 18, 26 barrel=roll_off The following setup groups are the same as group 91 below. 94:VLBA_SC 97:VLBA_NL 99:VLBA_OV 100:VLBA_MK Setup file: band.6-4 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 91 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 91 Setup file default. Used pcal sets: 3 LO sum= 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 BBC fr= 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 3 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 2510 2510 2510 2510 PCALFR2= 510 510 510 510 2510 2510 2510 2510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off The following setup groups are the same as group 92 below. 93:VLBA_LA 95:VLBA_FD 96:VLBA_HN 98:VLBA_BR Setup file: band.6-4 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 92 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 92 Setup file default. Used pcal sets: 3 LO sum= 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 BBC fr= 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 3 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 2510 2510 2510 2510 PCALFR2= 510 510 510 510 2510 2510 2510 2510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off The following setup groups are the same as group 101 below. 104:VLBA_SC 107:VLBA_NL 109:VLBA_OV 110:VLBA_MK Setup file: band.9050 Matches group v5090n in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 101 Station: VLBA_PT Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape used at high density at 160.000 ips. Time per pass is 22.00 minutes. 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 101 Setup file default. Used pcal sets: 4 LO sum= 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 BBC fr= 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 4 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 10 10 10 10 3010 3010 3010 3010 PCALFR2= 10 10 10 10 3010 3010 3010 3010 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 The following setup groups are the same as group 102 below. 103:VLBA_LA 105:VLBA_FD 106:VLBA_HN 108:VLBA_BR Setup file: band.9050 Matches group v5090n in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 102 Station: VLBA_KP Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Speedup factor: 1.00 Disk used to record data. 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 102 Setup file default. Used pcal sets: 4 LO sum= 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 BBC fr= 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 4 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 10 10 10 10 3010 3010 3010 3010 PCALFR2= 10 10 10 10 3010 3010 3010 3010 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 barrel=roll_off SUMMARY for experiment MT606 VLBA Monitoring Top item is: Seconds antenna is on source during scan. Bottom item is: Slew time in seconds from previous source. TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 42 is Sat 11 Feb 2006 MJD 53777 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Pt Kp La Sc Fd Hn Nl Br Ov Mk 42 07:47:31 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 07:54:00 band.21cm - 0 0 0 0 0 0 0 0 0 0 42 07:56:00 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:02:29 band.18cm - 6 7 6 6 6 6 6 8 14 6 42 08:03:29 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:09:58 band.13cm - 6 6 6 6 6 6 6 7 8 6 42 08:11:57 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:18:26 band.6cm - 6 7 6 6 6 6 6 8 8 6 42 08:19:26 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:25:55 band.4cm - 6 6 6 6 6 6 6 6 6 6 42 08:27:55 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:34:24 band.2cm - 6 6 6 6 6 6 6 7 6 6 42 08:35:24 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:41:52 band.1cm - 6 6 6 6 6 6 6 6 6 6 42 08:43:52 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:50:21 band.7mm - 6 6 6 6 6 6 6 7 6 6 42 08:52:21 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 08:58:50 band.6-16 - 6 6 6 6 6 6 6 7 6 6 42 08:59:50 0923+392 - 389 389 389 389 389 389 389 389 389 389 42 09:06:18 band.6-4 - 6 6 6 6 6 6 6 6 6 6 42 09:09:18 0923+392 - 479 479 479 479 479 479 479 479 479 479 42 09:17:17 band.9050 - 7 7 7 7 7 7 7 7 7 7 SUMMARY for experiment MT606 VLBA Monitoring Top item is: Seconds antenna is on source before scan start. Bottom item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 42 is Sat 11 Feb 2006 MJD 53777 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Pt Kp La Sc Fd Hn Nl Br Ov Mk 42 07:47:31 0923+392 - 0 0 0 0 0 0 0 0 0 0 42 07:54:00 band.21cm - 82 82 81 41 77 57 71 81 88 51 42 07:56:00 0923+392 - 113 112 113 113 113 113 113 112 105 113 42 08:02:29 band.18cm - 81 81 80 39 76 55 69 81 88 53 42 08:03:29 0923+392 - 54 54 54 54 54 54 54 53 51 54 42 08:09:58 band.13cm - 79 80 78 38 74 54 68 81 88 54 42 08:11:57 0923+392 - 113 113 113 113 113 113 113 112 112 113 42 08:18:26 band.6cm - 78 79 77 36 73 52 67 81 86 56 42 08:19:26 0923+392 - 54 54 54 54 54 54 54 53 54 54 42 08:25:55 band.4cm - 76 78 75 34 71 51 65 80 85 57 42 08:27:55 0923+392 - 113 113 113 113 113 113 113 112 113 113 42 08:34:24 band.2cm - 75 76 74 33 70 49 64 80 83 58 42 08:35:24 0923+392 - 54 54 54 54 54 54 54 54 54 54 42 08:41:52 band.1cm - 73 75 72 31 68 48 62 79 82 60 42 08:43:52 0923+392 - 113 113 113 113 113 113 113 113 113 113 42 08:50:21 band.7mm - 72 73 71 30 67 47 61 78 80 61 42 08:52:21 0923+392 - 113 113 113 113 113 113 113 113 113 113 42 08:58:50 band.6-16 - 70 72 69 28 65 45 59 77 79 62 42 08:59:50 0923+392 - 54 54 54 54 54 54 54 54 54 54 42 09:06:18 band.6-4 - 68 70 68 27 64 44 58 76 77 64 42 09:09:18 0923+392 - 172 172 172 172 172 173 173 173 172 173 42 09:17:17 band.9050 - 67 68 66 25 62 42 56 75 75 65 Automatic tape allocation requested for sites using VLBA control files and having 2 or more drives. SCHED cannot predict tape changes. Number of tapes or GBytes used at each autoaloc station: Includes all disk stations. Station Tapes GBytes VLBA_PT 0.12 VLBA_KP 70.4 VLBA_LA 70.4 VLBA_SC 0.12 VLBA_FD 70.4 VLBA_HN 70.4 VLBA_NL 0.12 VLBA_BR 70.4 VLBA_OV 0.12 VLBA_MK 0.12 ESTIMATED TAPE TIMES (With autoallocation): Times are approximate and assume project starts at the beginning of a tape. Times can be affected by actual tape length. Tape change may occur during scan preceeding indicated time. Tape start time. Tape end time. Station Day Time Day Time (UT) (UT) VLBA_PT 42 07:47:31 42 09:17:17 VLBA_KP 42 07:47:31 42 09:17:17 VLBA_LA 42 07:47:31 42 09:17:17 VLBA_SC 42 07:47:31 42 09:17:17 VLBA_FD 42 07:47:31 42 09:17:17 VLBA_HN 42 07:47:31 42 09:17:17 VLBA_NL 42 07:47:31 42 09:17:17 VLBA_BR 42 07:47:31 42 09:17:17 VLBA_OV 42 07:47:31 42 09:17:17 VLBA_MK 42 07:47:31 42 09:17:17 SOURCE LIST -- VLBA Monitoring Catalog positions marked with *. Precession of date coordinates is based on stop time of first scan. Names used in schedule marked with *. Short names used in VLA and SNAP files marked with +. Observation date used in B1950/J2000 coordinate conversion (PRECDATE): 1979.900 No adjustments are made for rates (DRA, DDEC). Scan hours are for recording scans only. Baseline hours are only counted for scans above horizon at both ends. Source Source position (RA/Dec) Error (B1950) (J2000) (Date) (mas) J0927+3902 09 23 55.319212 * 09 27 03.013933 09 27 27.957190 0.26 * 0923+392 39 15 23.56648 * 39 02 20.85188 39 00 44.74072 0.40 4C39.25 /home/filehost/cwalker/sched/catalogs/sources.vlba J0927+39 VLBA Calib Srcs - GSFC sols. - catalog 2004f_astro 1.213 scan hours, 54.601 baseline hours above horizon. The solar corona can cause unstable phases for sources too close to the Sun. SCHED provides warnings at individual scans for distances less than 10 degrees. The distance from the Sun to each source in this schedule is: Source Sun distance (deg) 0923+392 154.9 Barry Clark estimates from predictions by Ketan Desai of IPM scattering sizes that the Sun will cause amplitude reductions on the longest VLBA baselines at a solar distance of 60deg F^(-0.6) where F is in GHz. For common VLBI bands, this is: 327 MHz 117. deg 610 MHz 81. deg 1.6 GHz 45. deg 2.3 GHz 36. deg 5.0 GHz 23. deg 8.4 GHz 17. deg 15.0 GHz 12. deg 22.0 GHz 9. deg 43.0 GHz 6. deg J2000 coordinates formatted for possible transfer to the correlator data base: name = '0923+392' ra = 09h27m03.013933s dec = 39d02'20.85188" Catalogs: Station: /home/filehost/cwalker/sched/catalogs/stations.dat Version: 2006Jan23-09:50:23 Location: /home/filehost/cwalker/sched/catalogs/locations.dat Version: 08 Mar 2005 Frequency: /home/filehost/cwalker/sched/catalogs/freq.dat Version: 2006Jan23-09:50:23 Source: /home/filehost/cwalker/sched/catalogs/sources.vlba Version: 2005 March 1 Code versions: Release version: 6.02 July 2005 Version of VEX standard: 1.50 Version of VEX code: 0.85 Version of plot code: 1.05 Version of ephemeris code: 1.01 Version of PGPLOT: v5.2.0