SUMMARY FILE FOR PROJECT: MT507 COVER INFORMATION: Experiment: VLBA Monitoring Exp. Code: MT507 Start Day 47 is Wed 16 Feb 2005 MJD 53417 Schedule Version: 3.10 Processed by SCHED version: NRAO internal release of 4 October 2004 PI: Lorant Sjouwerman Address: NRAO-AOC P.O.Box O Socorro NM 87801, U.S.A. Phone: +1-505-838-4507 (home) EMAIL: lsjouwer@nrao.edu, analysts@nrao.edu Fax: Phone during observation: +1-505-835-7332 (work) Observing mode: VLBA 128MHz 8bbc 1bit R+L Notes: VLBA Monitoring test in dynamic scheduling and runs for 90 minutes (1.5 hours) total. Note: MAKE SURE ONE SOURCE IS SELECTED COVER LETTER: Please schedule ONE source depending on between approximately -3h to +3h of LST in Pie Town; a source can be selected by deleting the -one and only- ONE explanation mark in front of it. CORRELATION REQUESTS (Defaults in parentheses): Correlator (Required if recording): SOCORRO Correlator average time (2 sec): 1.835 sec. Alternate average time (for spacecraft). 0.000 sec. Spectral channels per baseband (16): 64 Number of antennas to be correlated: 10 Polarization (ON): ON Correlator weighting function (UNIFORM): UNIFORM Distribution tape (DAT): DAT Source positions from: SCHEDULE Shipping address for correlator output: Analysts Office NRAO-AOC P.O.Box O, Socorro NM 87801, U.S.A. Correlator Notes: Note: Job scripts will produce three different setups. VLBA auto-release test. Please correlate at highest priority. Please run sniffer promptly after correlation and directly after that get the data tape to the analysts (AOC mail box). ThanX.. DERIVED INFORMATION FOR CORRELATION: Elapsed time for project: 1.50 hours. Total time in scheduled scans: 1.21 hours. Total time in recording scans: 1.21 hours. Total number of baseline hours: 66.73 (Recording scans only) Projected maximum data output rate from the correlator: 245.5 kbytes/sec if processed in one pass. Projected correlator output data set size: 1024.8 Mbytes NOTE: Above numbers assume the same correlator parameters are used for all data. STATIONS USED IN SCHEDULE: Station Code Latitude Longitude Elevation X Y Z VLBA_PT Pt 34.30102 108.11919 2365. -1640953.71 -5014816.02 3575411.88 VLBA_KP Kp 31.95630 111.61242 1902. -1995678.63 -5037317.71 3357328.13 VLBA_LA La 35.77512 106.24560 1962. -1449752.36 -4975298.59 3709123.93 VLBA_SC Sc 17.75658 64.58363 -15. 2607848.52 -5488069.69 1932739.54 VLBA_FD Fd 30.63503 103.94482 1606. -1324009.13 -5332181.96 3231962.47 VLBA_HN Hn 42.93361 71.98658 296. 1446375.12 -4447939.65 4322306.12 VLBA_NL Nl 41.77142 91.57414 222. -130872.25 -4762317.11 4226851.04 VLBA_BR Br 48.13122 119.68328 251. -2112064.98 -3705356.52 4726813.80 VLBA_OV Ov 37.23165 118.27705 1196. -2409150.11 -4478573.23 3838617.40 VLBA_MK Mk 19.80138 155.45550 3763. -5464074.96 -2495249.12 2148296.84 BASELINE LENGTHS (km) Pt Kp La Sc Fd Hn Nl Br Ov Mk Pt 0 417 236 4579 564 3226 1663 1806 973 4795 Kp 417 0 652 4839 744 3623 2075 1913 845 4466 La 236 652 0 4458 608 3006 1432 1757 1088 4970 Sc 4579 4839 4458 0 4143 2853 3645 5767 5460 8611 Fd 564 744 608 4143 0 3105 1654 2345 1508 5134 Hn 3226 3623 3006 2853 3105 0 1611 3657 3885 7502 Nl 1663 2075 1432 3645 1654 1611 0 2300 2328 6156 Br 1806 1913 1757 5767 2345 3657 2300 0 1214 4398 Ov 973 845 1088 5460 1508 3885 2328 1214 0 4015 Mk 4795 4466 4970 8611 5134 7502 6156 4398 4015 0 RECORDING SYSTEM INFORMATION: TAPES - Stations potentially recording on tape. (See setup details later for times per pass.) Station Drives Head pos Tape len Density Start position Auto Auto Recorder (ft) Driv Head indx Aloc Reverse VLBA_PT 2 14 17600 High 1 1 Yes Yes VLBA VLBA_KP 2 14 17600 High 1 1 Yes Yes VLBA VLBA_LA 2 14 17600 High 1 1 Yes Yes VLBA VLBA_SC 2 14 17600 High 1 1 Yes Yes VLBA VLBA_FD 2 14 17600 High 1 1 Yes Yes VLBA VLBA_HN 2 14 17600 High 1 1 Yes Yes VLBA VLBA_NL 2 14 17600 High 1 1 Yes Yes VLBA VLBA_BR 2 14 17600 High 1 1 Yes Yes VLBA VLBA_OV 2 14 17600 High 1 1 Yes Yes VLBA VLBA_MK 2 14 17600 High 1 1 Yes Yes VLBA EXPERIMENT SUMMARY: Number of input scans: 11 Number of scans scheduled: 11 Number of stations: 10 Number of sources input: 1 Number of setup files used: 11 Station summaries (tape stations): Station Control Scans Scan Hours Tape hours Tapes Passes Readbacks VLBA_PT VLBA 11 1.21 1.21 1 4 6 VLBA_KP VLBA 11 1.21 1.21 1 4 6 VLBA_LA VLBA 11 1.21 1.21 1 4 6 VLBA_SC VLBA 11 1.21 1.21 1 4 6 VLBA_FD VLBA 11 1.21 1.21 1 4 6 VLBA_HN VLBA 11 1.21 1.21 1 4 6 VLBA_NL VLBA 11 1.21 1.21 1 4 6 VLBA_BR VLBA 11 1.21 1.21 1 4 6 VLBA_OV VLBA 11 1.21 1.21 1 4 6 VLBA_MK VLBA 11 1.21 1.21 1 4 6 Station summaries (disk stations): Station Control Scans Scan Hours Record hrs Gbytes Setup file: band.21cm Matches group v20cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 1 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 1 Setup file default. Used pcal sets: 1 LO sum= 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 BBC fr= 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.18cm Matches group v20cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 2 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 2 Setup file default. Used pcal sets: 1 LO sum= 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 BBC fr= 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.13cm Matches group v13cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 3 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 3 Setup file default. Used pcal sets: 1 LO sum= 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 BBC fr= 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.6cm Matches group v6cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 4 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 4 Setup file default. Used pcal sets: 1 LO sum= 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 BBC fr= 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 Setup file: band.4cm Matches group v4cm_3 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 5 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 5 Setup file default. Used pcal sets: 1 LO sum= 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 BBC fr= 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.2cm Matches group v2cm_d3 in /home/arana/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 6 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 6 Setup file default. Used pcal sets: 1 LO sum= 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 BBC fr= 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_auto Setup file: band.1cm Matches group v1cm_b3 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 7 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 1cm omit 1cm VLBA Synth= 9.1 15.4 12.4 The following frequency sets based on this setup were used. Frequency Set: 7 Setup file default. Used pcal sets: 1 LO sum= 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 Setup file: band.7mm Matches group v7mm_c8 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 8 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 7mm omit 7mm omit VLBA Synth= 15.4 7.6 11.6 The following frequency sets based on this setup were used. Frequency Set: 8 Setup file default. Used pcal sets: 1 LO sum= 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.6-16 Matches group v6cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 9 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 4 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U Pol. = RCP LCP RCP LCP BBC = 1 2 3 4 BBC SB= U U U U IF = A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 9 Setup file default. Used pcal sets: 2 LO sum= 4974.49 4974.49 4990.49 4990.49 BBC fr= 874.49 874.49 890.49 890.49 Bandwd= 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 2 PCAL = 1MHZ PCALXB1= S1 S3 S1 S3 S1 S3 S1 S3 PCALXB2= S2 S4 S2 S4 S2 S4 S2 S4 PCALFR1= 510 510 13510 13510 0 0 1510 1510 PCALFR2= 510 510 13510 13510 0 0 1510 1510 Track assignments are: track1= 2, 10, 18, 26 track2= 3, 11, 19, 27 barrel=roll_auto Setup file: band.6-4 Matches group v6cm_2 in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 10 Station: VLBA Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 10 Setup file default. Used pcal sets: 3 LO sum= 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 BBC fr= 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 3 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 2510 2510 2510 2510 PCALFR2= 510 510 510 510 2510 2510 2510 2510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.9050 Matches group v5090n in /home/arana/cwalker/sched/catalogs/freq.dat Setup group: 11 Station: VLBA Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 11 Setup file default. Used pcal sets: 4 LO sum= 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 BBC fr= 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 4 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 10 10 10 10 3010 3010 3010 3010 PCALFR2= 10 10 10 10 3010 3010 3010 3010 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 SUMMARY for experiment MT507 VLBA Monitoring Top item is: Seconds antenna is on source during scan. Bottom item is: Slew time in seconds from previous source. TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 47 is Wed 16 Feb 2005 MJD 53417 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Pt Kp La Sc Fd Hn Nl Br Ov Mk 47 06:47:01 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 06:53:30 band.21cm - 0 0 0 0 0 0 0 0 0 0 47 06:55:30 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:01:59 band.18cm - 9 8 10 6 7 6 6 7 6 6 47 07:02:59 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:09:28 band.13cm - 7 7 7 6 6 6 6 6 6 6 47 07:11:27 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:17:56 band.6cm - 8 8 7 6 7 6 6 7 7 6 47 07:18:56 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:25:25 band.4cm - 6 7 6 6 6 6 6 6 7 6 47 07:27:25 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:33:54 band.2cm - 7 8 6 6 6 6 6 7 10 6 47 07:34:53 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:41:22 band.1cm - 6 6 6 6 6 6 6 7 10 6 47 07:43:22 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:49:51 band.7mm - 6 7 6 6 6 6 6 8 11 6 47 07:51:51 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 07:58:20 band.6-16 - 6 7 6 6 6 6 6 8 8 6 47 07:59:19 0923+392 - 389 389 389 389 389 389 389 389 389 389 47 08:05:48 band.6-4 - 6 6 6 6 6 6 6 6 6 6 47 08:08:48 0923+392 - 479 479 479 479 479 479 479 479 479 479 47 08:16:47 band.9050 - 7 7 7 7 7 7 7 8 7 7 SUMMARY for experiment MT507 VLBA Monitoring Top item is: Seconds antenna is on source before scan start. Bottom item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 47 is Wed 16 Feb 2005 MJD 53417 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Pt Kp La Sc Fd Hn Nl Br Ov Mk 47 06:47:01 0923+392 - 0 0 0 0 0 0 0 0 0 0 47 06:53:30 band.21cm - 85 82 87 48 81 64 78 77 80 44 47 06:55:30 0923+392 - 111 112 110 113 112 113 113 113 113 113 47 07:01:59 band.18cm - 85 82 86 47 81 62 77 78 82 45 47 07:02:59 0923+392 - 52 53 53 54 54 54 54 54 54 54 47 07:09:28 band.13cm - 85 83 85 45 80 61 76 79 83 47 47 07:11:27 0923+392 - 112 112 112 113 113 113 113 113 113 113 47 07:17:56 band.6cm - 84 83 84 44 79 60 74 79 85 48 47 07:18:56 0923+392 - 53 53 54 54 54 54 54 53 53 54 47 07:25:25 band.4cm - 83 83 83 42 78 58 73 80 86 50 47 07:27:25 0923+392 - 113 112 113 113 113 113 113 112 109 113 47 07:33:54 band.2cm - 82 82 81 41 77 57 71 81 88 51 47 07:34:53 0923+392 - 54 54 54 54 54 54 54 53 50 54 47 07:41:22 band.1cm - 81 81 80 39 76 55 70 81 88 53 47 07:43:22 0923+392 - 113 113 113 113 113 113 113 112 109 113 47 07:49:51 band.7mm - 79 80 78 37 74 54 68 81 88 54 47 07:51:51 0923+392 - 113 113 113 113 113 113 113 112 112 113 47 07:58:20 band.6-16 - 78 79 77 36 73 52 66 81 86 56 47 07:59:19 0923+392 - 54 54 54 54 54 54 54 53 54 54 47 08:05:48 band.6-4 - 76 77 75 34 71 51 65 80 85 57 47 08:08:48 0923+392 - 172 173 172 172 173 173 173 172 172 173 47 08:16:47 band.9050 - 74 76 73 32 70 49 63 80 83 59 Automatic tape allocation requested for sites using VLBA control files and having 2 or more drives. SCHED cannot predict tape changes. Number of tapes used at each autoaloc station: Station Tapes VLBA_PT 0.12 VLBA_KP 0.12 VLBA_LA 0.12 VLBA_SC 0.12 VLBA_FD 0.12 VLBA_HN 0.12 VLBA_NL 0.12 VLBA_BR 0.12 VLBA_OV 0.12 VLBA_MK 0.12 ESTIMATED TAPE TIMES (With autoallocation): Times are approximate and assume project starts at the beginning of a tape. Times can be affected by actual tape length. Tape change may occur during scan preceeding indicated time. Tape start time. Tape end time. Station Day Time Day Time (UT) (UT) VLBA_PT 47 06:47:01 47 08:16:47 VLBA_KP 47 06:47:01 47 08:16:47 VLBA_LA 47 06:47:01 47 08:16:47 VLBA_SC 47 06:47:01 47 08:16:47 VLBA_FD 47 06:47:01 47 08:16:47 VLBA_HN 47 06:47:01 47 08:16:47 VLBA_NL 47 06:47:01 47 08:16:47 VLBA_BR 47 06:47:01 47 08:16:47 VLBA_OV 47 06:47:01 47 08:16:47 VLBA_MK 47 06:47:01 47 08:16:47 SOURCE LIST -- VLBA Monitoring Catalog positions marked with *. Precession of date coordinates is based on stop time of first scan. Names used in schedule marked with *. Short names used in VLA and SNAP files marked with +. Observation date used in B1950/J2000 coordinate conversion (PRECDATE): 1979.900 No adjustments are made for rates (DRA, DDEC). Scan hours are for recording scans only. Baseline hours are only counted for scans above horizon at both ends. Source Source position (RA/Dec) (B1950) (J2000) (Date) J0927+3902 09 23 55.319195 * 09 27 03.013916 09 27 23.787920 * 0923+392 39 15 23.56655 * 39 02 20.85195 39 01 02.47733 4C39.25 /home/arana/cwalker/sched/catalogs/sources.vlba J0927+39 ICRF - Ext.1 Source - 1998 IERS Annual Report 1.213 scan hours, 54.601 baseline hours above horizon. The solar corona can cause unstable phases for sources too close to the Sun. SCHED provides warnings at individual scans for distances less than 10 degrees. The distance from the Sun to each source in this schedule is: Source Sun distance (deg) 0923+392 152.3 Barry Clark estimates from predictions by Ketan Desai of IPM scattering sizes that the Sun will cause amplitude reductions on the longest VLBA baselines at a solar distance of 60deg F^(-0.6) where F is in GHz. For common VLBI bands, this is: 327 MHz 117. deg 610 MHz 81. deg 1.6 GHz 45. deg 2.3 GHz 36. deg 5.0 GHz 23. deg 8.4 GHz 17. deg 15.0 GHz 12. deg 22.0 GHz 9. deg 43.0 GHz 6. deg J2000 coordinates formatted for possible transfer to the correlator data base: name = '0923+392' ra = 09h27m03.013916s dec = 39d02'20.85195" Catalog versions: Station Catalog: 2004Oct03-17:33:37 Frequency Catalog: 2004Oct03-17:33:37 Code versions: Release version: NRAO internal release of 4 October 2004 Version of sched code: 5.25 Version of VEX standard: 1.50 Version of VEX code: 0.79 Version of plot code: 1.05 Version of ephemeris code: 1.01 Version of PGPLOT: v5.2.0