Welcome to program SCHED.  Version: Release of 18 Sept. 2003

The manual is at http://www.aoc.nrao.edu/~cwalker/sched/sched/sched.html
Unix users should set $SCHED to the base area where SCHED is installed.
** NEW ** Most run time messages will be in sched.runlog

Some useful commands to give now if running interactively:
   SCHedule=<filename>    :  Specify input file.
   PLOT                   :  Invokes uv, xy, rd, and uptime plotting.
   FREQLIST=lowF,highF    :  Make frequency list (MHz).  Then exit.
   EXIT                   :  Leave program.
   /                      :  End of inputs - run program (or EXIT).

TPINI:   Reading tape initialization information from SCHED input file.
SRREAD:  Reading source catalog: Program_input
SRREAD:  Please convert source catalog from use of EPOCH to EQUINOX.
RDSET:   Reading setup file: GM059A.4cm
STREAD:  Reading station catalog: /sched-2003/catalogs/stations.dat
STREAD:  Will read locations file /sched-2003/catalogs/locations.dat
SCHIN:   Found   317 input scans.
SCHIN:   * Automatic tape allocation requested at: Br Fd Hn Kp La Mk Nl Pt Ov Sc Y Gb
GETFREQ: Reading frequency file: /sched-2003/catalogs/freq.dat.2004sep27
SETFCAT: In setup: GM059A.4cm
         Station VLA27
         Only   50.00 of   64.00 MHz total bandwidth is within the IFs
         in the setup file before any FREQ or DOPPLER shifts.
SETFCAT: In setup: GM059A.4cm
         Station ROB70
         Only   47.49 of   64.00 MHz total bandwidth is within the IFs
         in the setup file before any FREQ or DOPPLER shifts.
SETFCAT: In setup: GM059A.4cm
         Station GOLD70
         Only   47.49 of   64.00 MHz total bandwidth is within the IFs
         in the setup file before any FREQ or DOPPLER shifts.
SCHOPT:  First output scan will be number     1

WRTMSG: Special message from routine AUTODOWN:

  * Stations using automatic tape allocation are being removed
    from scans when the source is below the antenna pointing limits.

SCHOPT:  There will be   317 output scans (    1 -   317) from  51/14:07:00 to  52/01:55:53
SCHTIM: Caution: Only     4 readback tests (2 min gaps) at GOLD70
        Please try for at least one readback each two hours.
SCHTIM:  VLBA_BR  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_FD  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_HN  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_KP  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_LA  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_MK  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_NL  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_PT  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_OV  averages more than 10 tape stops per hour.
SCHTIM:  VLBA_SC  averages more than 10 tape stops per hour.
SCHTIM:  VLA27    averages more than 10 tape stops per hour.
SCHTIM:  EB_VLBA  averages more than 10 tape stops per hour.
SCHTIM:  MEDICINA averages more than 10 tape stops per hour.
SCHTIM:  GBT_VLBA averages more than 10 tape stops per hour.
SCHTIM:  ROB70    averages more than 10 tape stops per hour.
SCHTIM:  GOLD70   averages more than 10 tape stops per hour.
   Tape synchronization on the  VLBA correlator is better
   when the tape does not stop often.  Parameters MINPAUSE
   and PRESTART may be used to encourage continuous tape motion.
FSFREQ: **** VLA BBC frequency (    656.41) outside normal
FSFREQ:     range (600-650) at the VLA
SUMOPE:  Writing summary file gm059a.sum
OMSOUT:  Writing OMS file gm059a.oms
VXWRT :  Writing  V E X  file gm059a.skd
FLAGS:   Writing apriori flagging file gm059a.flag
 Processing VLBA_BR
 Processing VLBA_FD
 Processing VLBA_HN
 Processing VLBA_KP
 Processing VLBA_LA
 Processing VLBA_MK
 Processing VLBA_NL
 Processing VLBA_PT
 Processing VLBA_OV
 Processing VLBA_SC
 Processing VLA27
 Processing EB_VLBA
 Processing MEDICINA
 Processing GBT_VLBA
 Processing ROB70
 Processing GOLD70