Welcome to program SCHED. Version: NRAO internal release of 4 October 2004 The manual is at http://www.aoc.nrao.edu/~cwalker/sched/sched/sched.html Unix users should set $SCHED to the base area where SCHED is installed. ** NEW ** Most run time messages will be in sched.runlog Some useful commands to give now if running interactively: SCHedule= : Specify input file. PLOT : Invokes uv, xy, rd, and uptime plotting. FREQLIST=lowF,highF : Make frequency list (MHz). Then exit. EXIT : Leave program. / : End of inputs - run program (or EXIT). RDSET: Reading setup file: v7mm-sio.set RDSET: Reading setup file: v7mm-sio-vla.set RDSET: Reading setup file: v3mm-sio.set SRREAD: Reading source catalog: Program_input STREAD: Reading station catalog: /home/filehost/cwalker/sched/catalogs/stations.dat STREAD: Will read locations file /home/filehost/cwalker/sched/catalogs/locations.dat SCHIN: Found 48 input scans. SCHIN: * Automatic tape allocation requested at: Nl Fd La Pt Kp Ov Mk Br Hn Y SATTIM: WARNING - Both GAP and START specified. Will use START. Scan: 25 TPINI: Using default tape initialization information. SRREAD: Reading source catalog: /home/filehost/cwalker/sched/catalogs/sources.vlba RDSET: Reading setup file: /home/filehost/cwalker/sched/setups/pt7mm.set GETFREQ: Reading frequency file: /home/filehost/cwalker/sched/catalogs/freq.dat SETFCAT: In setup: v7mm-sio-vla.set Station VLA1 WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band y_vq 1 2 T T T T T T T T y_vq 2 4 T T T T T T T T y_vq 3 2 T T T T T T T T y_vq 4 4 T T T T T T T T y_vq 5 2 T T T T T T T T y_vq 6 4 T T T T T T T T y_vq 7 2 T T T T T T F T y_vq 8 4 T T T T T T F T FCOMPARE: The problem is with the match of VLA parameters (F indicates mismatch): FLUKEA FLUKEB VLAFEAB VLAFECD VLASYNA VLASYNB FEFILTER VLABAND VLABW T T T F F F T T T y_43139.9j 1 2 T F T T T T T T y_43139.9j 2 4 T F T T T T T T y_43139.9j 3 2 T F T T T T T T y_43139.9j 4 4 T F T T T T T T y_43139.9j 5 2 T F T T T T T T y_43139.9j 6 4 T F T T T T T T y_43139.9j 7 2 T F T T T T T T y_43139.9j 8 4 T F T T T T T T y_43160.1j 7 2 T F T T T T T T y_43160.1j 8 4 T F T T T T T T --------------------------------------- SCHOPT: First output scan will be number 49 WRTMSG: Special message from routine AUTODOWN: * Stations using automatic tape allocation are being removed from scans when the source is below the antenna pointing limits. SCHOPT: There will be 62 output scans ( 49 - 110) from 43/05:01:55 to 43/11:00:00 SCHTIM: Earliest output scan start time differs from earliest in input schedule. This may be due to an inserted reference pointing scan. SUMOPE: Writing summary file bk113e.sum OMSOUT: Writing OMS file bk113e.oms FLAGS: Writing apriori flagging file bk113e.flag Processing VLBA_NL Processing VLBA_FD Processing VLBA_LA Processing VLBA_PT Processing VLBA_KP Processing VLBA_OV Processing VLBA_MK Processing VLBA_BR Processing VLBA_HN Processing VLA1