COVER INFORMATION Station: VLBA_KP (Code Kp ) Experiment: VLBA Monitoring Exp. Code: MT407 Schedule Version: 3.10 Processed by SCHED version: Release of 18 Sept. 2003 PI: Lorant Sjouwerman Address: NRAO-AOC P.O.Box O Socorro NM 87801, U.S.A. Phone: +1-505-838-4507 (home) EMAIL: lsjouwer@nrao.edu, analysts@nrao.edu Fax: Phone during observation: +1-505-835-7332 (work) Observing mode: VLBA 128MHz 8bbc 1bit R+L Notes: VLBA Monitoring test in dynamic scheduling and runs for 90 minutes (1.5 hours) total. Note: MAKE SURE ONE SOURCE IS SELECTED COVER LETTER: Please schedule ONE source depending on between approximately -3h to +3h of LST in Pie Town; a source can be selected by deleting the -one and only- ONE explanation mark in front of it. Schedule for VLBA_KP (Code Kp ) Page 2 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 18 Feb 2004 Day 49 --- Next scan frequencies: 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 Next BBC frequencies: 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Next scan bandwidths: 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 09 27 41 0923+392 11 52 02 59.9 -66.2 2.4 92.3 0 1 1 0 09 27 41 09 34 10 --- 11 58 32 58.7 -66.3 2.5 91.2 389 F 1 5186 Next scan frequencies: 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 Next BBC frequencies: 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 09 36 10 0923+392 12 00 32 58.3 -66.3 2.6 90.9 113 1 1 5186 09 36 10 09 42 39 --- 12 07 02 57.0 -66.3 2.7 89.8 389 F 1 10372 Next scan frequencies: 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 Next BBC frequencies: 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 09 43 38 0923+392 12 08 02 56.8 -66.3 2.7 89.7 54 1 1 10372 09 43 38 09 50 07 --- 12 14 32 55.6 -66.3 2.8 88.7 389 F 1 15557 Next scan frequencies: 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 Next BBC frequencies: 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 09 52 07 0923+392 12 16 32 55.2 -66.2 2.8 88.4 113 1 2 15557 09 52 07 09 58 36 --- 12 23 02 53.9 -66.2 2.9 87.4 389 R 1 14457 Next scan frequencies: 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 Next BBC frequencies: 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 09 59 36 0923+392 12 24 02 53.7 -66.2 2.9 87.3 54 1 2 14457 09 59 36 10 06 05 --- 12 30 32 52.4 -66.0 3.1 86.4 389 R 1 9271 Schedule for VLBA_KP (Code Kp ) Page 3 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 18 Feb 2004 Day 49 --- Next scan frequencies: 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 Next BBC frequencies: 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 10 08 04 0923+392 12 32 32 52.1 -66.0 3.1 86.1 113 1 2 9271 10 08 04 10 14 33 --- 12 39 02 50.8 -65.8 3.2 85.2 389 R 1 4085 Next scan frequencies: 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 Next BBC frequencies: 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 10 15 33 0923+392 12 40 02 50.6 -65.8 3.2 85.0 54 1 1 4085 10 15 33 10 22 02 --- 12 46 32 49.4 -65.6 3.3 84.2 389 F 2 1101 Next scan frequencies: 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 Next BBC frequencies: 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 10 24 02 0923+392 12 48 32 49.0 -65.6 3.4 83.9 113 1 1 1101 10 24 02 10 30 31 --- 12 55 02 47.7 -65.4 3.5 83.0 389 F 2 6286 Next scan frequencies: 4974.49 4974.49 4990.49 4990.49 Next BBC frequencies: 874.49 874.49 890.49 890.49 Next scan bandwidths: 16.00 16.00 16.00 16.00 10 32 30 0923+392 12 57 02 47.3 -65.3 3.5 82.8 113 1 1 6286 10 32 30 10 38 59 --- 13 03 32 46.1 -65.0 3.6 81.9 389 F 2 11472 Next scan frequencies: 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 Next BBC frequencies: 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Next scan bandwidths: 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 10 39 59 0923+392 13 04 32 45.9 -65.0 3.6 81.8 54 1 1 11472 10 39 59 10 46 28 --- 13 11 02 44.6 -64.7 3.7 81.0 389 F 2 16658 Schedule for VLBA_KP (Code Kp ) Page 4 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 18 Feb 2004 Day 49 --- Next scan frequencies: 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 Next BBC frequencies: 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 10 49 28 0923+392 13 14 02 44.1 -64.6 3.8 80.6 172 1 2 16658 10 49 28 10 57 26 --- 13 22 02 42.5 -64.2 3.9 79.6 479 R 2 12159 SETUP FILE INFORMATION: NOTE: If DOPPLER, FREQ, or BW were used, see the individual scans for the final BBC settings. Setup file: band.21cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 1 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 1 Setup file default. Used pcal sets: 1 LO sum= 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 BBC fr= 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.18cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 2 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 2 Setup file default. Used pcal sets: 1 LO sum= 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 BBC fr= 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.13cm Matches group v13cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 3 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 3 Setup file default. Used pcal sets: 1 LO sum= 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 BBC fr= 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.6cm Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 4 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 4 Setup file default. Used pcal sets: 1 LO sum= 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 BBC fr= 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 Setup file: band.4cm Matches group v4cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 5 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 5 Setup file default. Used pcal sets: 1 LO sum= 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 BBC fr= 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.2cm Matches group v2cm_d3 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 6 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 6 Setup file default. Used pcal sets: 1 LO sum= 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 BBC fr= 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_auto Setup file: band.1cm Matches group v1cm_b3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 7 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 1cm omit 1cm VLBA Synth= 9.1 15.4 12.4 The following frequency sets based on this setup were used. Frequency Set: 7 Setup file default. Used pcal sets: 1 LO sum= 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 Setup file: band.7mm Matches group v7mm_c8 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 8 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 7mm omit 7mm omit VLBA Synth= 15.4 7.6 11.6 The following frequency sets based on this setup were used. Frequency Set: 8 Setup file default. Used pcal sets: 1 LO sum= 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.6-16 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 9 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 4 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U Pol. = RCP LCP RCP LCP BBC = 1 2 3 4 BBC SB= U U U U IF = A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 9 Setup file default. Used pcal sets: 2 LO sum= 4974.49 4974.49 4990.49 4990.49 BBC fr= 874.49 874.49 890.49 890.49 Bandwd= 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 2 PCAL = 1MHZ PCALXB1= S1 S3 S1 S3 S1 S3 S1 S3 PCALXB2= S2 S4 S2 S4 S2 S4 S2 S4 PCALFR1= 510 510 13510 13510 0 0 1510 1510 PCALFR2= 510 510 13510 13510 0 0 1510 1510 Track assignments are: track1= 2, 10, 18, 26 track2= 3, 11, 19, 27 barrel=roll_auto Setup file: band.6-4 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 10 Station: VLBA Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 10 Setup file default. Used pcal sets: 3 LO sum= 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 BBC fr= 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 3 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 2510 2510 2510 2510 PCALFR2= 510 510 510 510 2510 2510 2510 2510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.9050 Matches group v5090n in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 11 Station: VLBA Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 11 Setup file default. Used pcal sets: 4 LO sum= 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 BBC fr= 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 4 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 10 10 10 10 3010 3010 3010 3010 PCALFR2= 10 10 10 10 3010 3010 3010 3010 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 SOURCE LIST -- VLBA Monitoring Catalog positions marked with *. Precession of date coordinates is based on stop time of first scan. Names used in schedule marked with *. Short names used in VLA and SNAP files marked with +. Observation date used in B1950/J2000 coordinate conversion (PRECDATE): 1979.900 No adjustments are made for rates (DRA, DDEC). Source Source position (RA/Dec) (B1950) (J2000) (Date) J0927+3902 09 23 55.319195 * 09 27 03.013916 09 27 19.662557 * 0923+392 39 15 23.56655 * 39 02 20.85195 39 01 18.65901 4C39.25 /home/filehost/cwalker/sched/catalogs/sources.vlba J0927+39 ICRF - Ext.1 Source - 1998 IERS Annual Report The solar corona can cause unstable phases for sources too close to the Sun. SCHED provides warnings at individual scans for distances less than 10 degrees. The distance from the Sun to each source in this schedule is: Source Sun distance (deg) 0923+392 151.5 Barry Clark estimates from predictions by Ketan Desai of IPM scattering sizes that the Sun will cause amplitude reductions on the longest VLBA baselines at a solar distance of 60deg F^(-0.6) where F is in GHz. For common VLBI bands, this is: 327 MHz 117. deg 610 MHz 81. deg 1.6 GHz 45. deg 2.3 GHz 36. deg 5.0 GHz 23. deg 8.4 GHz 17. deg 15.0 GHz 12. deg 22.0 GHz 9. deg 43.0 GHz 6. deg