COVER INFORMATION Station: VLBA_OV (Code Ov ) Experiment: VLBA Monitoring Exp. Code: TR017E Schedule Version: 2.10 Processed by SCHED version: Release of 02 July 2002 PI: Lorant Sjouwerman Address: NRAO-AOC P.O.Box O Socorro NM 87801, U.S.A. Phone: +1-505-838-4507 (home) EMAIL: lsjouwerman@aoc.nrao.edu Fax: Phone during observation: +1-505-835-7332 (work) Observing mode: VLBA 128MHz 8bbc 1bit R+L Notes: VLBA Monitoring test in dynamic scheduling Note: MAKE SURE ONE SOURCE IS SELECTED COVER LETTER: Please schedule ONE source depending on between approximately -3h to +3h of LST in Pie Town; a source can be selected by deleting the -one and only- ONE explanation mark in front of it. Schedule for VLBA_OV (Code Ov ) Page 2 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 26 Feb 2003 Day 57 --- Next scan frequencies: 314.49 314.49 322.49 322.49 330.49 330.49 338.49 338.49 Next BBC frequencies: 814.49 814.49 822.49 822.49 830.49 830.49 838.49 838.49 Next scan bandwidths: 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 10 48 58 1308+326 13 19 22 84.8 200.7 0.1 19.5 0 1 1 0 10 48 58 10 57 56 --- 13 28 22 83.9 217.9 0.3 35.3 539 F 1 3590 Next scan frequencies: 594.98 594.98 602.98 602.98 610.98 610.98 618.98 618.98 Next BBC frequencies: 594.98 594.98 602.98 602.98 610.98 610.98 618.98 618.98 10 59 56 1308+326 13 30 22 83.6 221.0 0.3 38.2 112 1 1 3590 10 59 56 11 04 55 --- 13 35 22 82.9 227.8 0.4 44.3 299 F 1 5585 Next scan frequencies: 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 Next BBC frequencies: 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 11 04 55 1308+326 13 35 22 82.9 227.8 0.4 44.3 -6 1 1 5585 11 04 55 11 09 55 --- 13 40 22 82.2 233.4 0.5 49.1 293 F 1 7579 Next scan frequencies: 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 Next BBC frequencies: 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 11 09 55 1308+326 13 40 22 82.2 233.4 0.5 49.1 -6 1 1 7579 11 09 55 11 14 54 --- 13 45 22 81.3 238.0 0.6 53.1 293 F 1 9574 Next scan frequencies: 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 Next BBC frequencies: 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 11 14 54 1308+326 13 45 22 81.3 238.0 0.6 53.1 -6 1 1 9574 11 14 54 11 19 53 --- 13 50 22 80.5 241.9 0.7 56.2 293 F 1 11568 Schedule for VLBA_OV (Code Ov ) Page 3 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 26 Feb 2003 Day 57 --- Next scan frequencies: 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 Next BBC frequencies: 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 11 21 53 1308+326 13 52 22 80.1 243.3 0.7 57.3 113 1 1 11568 11 21 53 11 26 52 --- 13 57 22 79.2 246.4 0.8 59.7 299 F 1 13563 Next scan frequencies: 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 Next BBC frequencies: 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 11 26 52 1308+326 13 57 22 79.2 246.4 0.8 59.7 -6 1 1 13563 11 26 52 11 31 51 --- 14 02 22 78.3 249.0 0.9 61.6 293 F 1 15557 Next scan frequencies: 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 Next BBC frequencies: 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 11 31 51 1308+326 14 02 22 78.3 249.0 0.9 61.6 -6 1 1 15557 11 31 51 11 36 50 --- 14 07 22 77.4 251.3 0.9 63.2 293 F 1 17552 Next scan frequencies: 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 Next BBC frequencies: 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 11 36 50 1308+326 14 07 22 77.4 251.3 0.9 63.2 -6 1 2 17552 11 36 50 11 41 49 --- 14 12 22 76.4 253.4 1.0 64.5 293 R 1 15557 Next scan frequencies: 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 Next BBC frequencies: 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 11 43 49 1308+326 14 14 22 76.0 254.1 1.1 65.0 113 1 2 15557 11 43 49 11 48 48 --- 14 19 22 75.1 255.9 1.1 66.0 299 R 1 13563 SETUP FILE INFORMATION: NOTE: If DOPPLER, FREQ, or BW were used, see the individual scans for the final BBC settings. Setup file: band.90cm Matches group v5090n in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 1 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 1 Setup file default. Used pcal sets: 1 LO sum= 314.49 314.49 322.49 322.49 330.49 330.49 338.49 338.49 BBC fr= 814.49 814.49 822.49 822.49 830.49 830.49 838.49 838.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: band.50cm Matches group v5090w in /home/filehost/cwalker/sched/catalogs/freq.dat Wide 50 cm filter. Beware RFI. Some stations will saturate. Setup group: 2 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 2 Setup file default. Used pcal sets: 2 LO sum= 594.98 594.98 602.98 602.98 610.98 610.98 618.98 618.98 BBC fr= 594.98 594.98 602.98 602.98 610.98 610.98 618.98 618.98 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 2 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 20 20 20 20 6020 6020 6020 6020 PCALFR2= 20 20 20 20 6020 6020 6020 6020 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_16 Setup file: band.21cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 3 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 3 Setup file default. Used pcal sets: 1 LO sum= 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 BBC fr= 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_8 Setup file: band.18cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 4 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 4 Setup file default. Used pcal sets: 1 LO sum= 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 BBC fr= 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_off Setup file: band.13cm Matches group v13cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 5 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 5 Setup file default. Used pcal sets: 1 LO sum= 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 BBC fr= 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_8 Setup file: band.6cm Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 6 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 6 Setup file default. Used pcal sets: 1 LO sum= 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 BBC fr= 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_16 Setup file: band.4cm Matches group v4cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 7 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 7 Setup file default. Used pcal sets: 1 LO sum= 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 BBC fr= 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_off Setup file: band.2cm Matches group v2cm_d3 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 8 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 8 Setup file default. Used pcal sets: 1 LO sum= 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 BBC fr= 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: band.1cm Matches group v1cm_b3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 9 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 1cm omit 1cm VLBA Synth= 9.1 15.4 12.4 The following frequency sets based on this setup were used. Frequency Set: 9 Setup file default. Used pcal sets: 1 LO sum= 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_16 Setup file: band.7mm Matches group v7mm_c8 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 10 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 2.00 Tape speeds: Low density - 133.330 ips, High density - 80.00 ips Time per pass for 17600 ft, High density tapes is: 00:44:00 1st LO= 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 7mm omit 7mm omit VLBA Synth= 15.4 7.6 11.6 The following frequency sets based on this setup were used. Frequency Set: 10 Setup file default. Used pcal sets: 1 LO sum= 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_8 SOURCE LIST -- VLBA Monitoring Catalog positions marked with *. Precession of date coordinates is based on stop time of first scan. Names used in schedule marked with *. Short names used in VLA and SNAP files marked with +. Observation date used in B1950/J2000 coordinate conversion (PRECDATE): 1979.900 No adjustments are made for rates (DRA, DDEC). Source Source position (RA/Dec) (B1950) (J2000) (Date) J1310+3220 13 08 07.560126 * 13 10 28.663845 13 10 38.052876 * 1308+326 32 36 40.23888 * 32 20 43.78295 32 19 34.16647 J1310+32 /home/filehost/cwalker/sched/catalogs/sources.vlba ICRF - Ext.1 Source - 1998 IERS Annual Report The solar corona can cause unstable phases for sources too close to the Sun. SCHED provides warnings at individual scans for distances less than 10 degrees. The distance from the Sun to each source in this schedule is: Source Sun distance (deg) 1308+326 137.3 Barry Clark estimates from predictions by Ketan Desai of IPM scattering sizes that the Sun will cause amplitude reductions on the longest VLBA baselines at a solar distance of 60deg F^(-0.6) where F is in GHz. For common VLBI bands, this is: 327 MHz 117. deg 610 MHz 81. deg 1.6 GHz 45. deg 2.3 GHz 36. deg 5.0 GHz 23. deg 8.4 GHz 17. deg 15.0 GHz 12. deg 22.0 GHz 9. deg 43.0 GHz 6. deg