SUMMARY FILE FOR PROJECT: tr016 COVER INFORMATION: Experiment: VLBA RFI survey: 90, 50, 20, 13, 6, 4, 2cm. Exp. Code: tr016 Schedule Version: 1.00 Processed by SCHED version: 16 Oct. 2001 PI: D.Mertely Address: NRAO P. O. Box O Socorro, NM 87801 USA Phone: 505-835-7128 EMAIL: Internet: dmertely@nrao.edu Fax: 505-835-7027 Phone during observation: 505-835-7128 Observing mode: VLBA Notes: VLBA RFI survey: 90, 50, 20, 13, 6, 4, 2cm. No cover letter provided. CORRELATION REQUESTS (Defaults in parentheses): Correlator (Required if recording): SOCORRO Correlator average time (2 sec): 5.000 sec. Alternate average time (for spacecraft). 0.000 sec. Spectral channels per baseband (16): 256 Number of antennas to be correlated: 10 Polarization (ON): OFF Correlator weighting function (UNIFORM): ZEROPAD Distribution tape (DAT): DAT Source positions from: TR015.SUM FILE Shipping address for correlator output: Dan Mertely Correlator Notes: DERIVED INFORMATION FOR CORRELATION: Elapsed time for project: 4.96 hours. Total time in scheduled scans: 5.02 hours. Total time in recording scans: 4.61 hours. Total number of baseline hours: 253.46 (Recording scans only) Projected maximum data output rate from the correlator: 180.2 kbytes/sec if processed in one pass. Projected correlator output data set size: 2989.9 Mbytes NOTE: Above numbers assume the same correlator parameters are used for all data. STATIONS USED IN SCHEDULE: Station Code Latitude Longitude Elevation X Y Z VLBA_SC Sc 17.76 64.58 -14. 2607848.52 -5488069.68 1932739.53 VLBA_HN Hn 42.93 71.99 297. 1446375.13 -4447939.65 4322306.12 VLBA_NL Nl 41.77 91.57 223. -130872.24 -4762317.12 4226851.04 VLBA_FD Fd 30.64 103.94 1607. -1324009.12 -5332181.97 3231962.47 VLBA_LA La 35.78 106.25 1963. -1449752.35 -4975298.59 3709123.93 VLBA_PT Pt 34.30 108.12 2366. -1640953.70 -5014816.03 3575411.88 VLBA_KP Kp 31.96 111.61 1903. -1995678.62 -5037317.71 3357328.13 VLBA_OV Ov 37.23 118.28 1197. -2409150.10 -4478573.23 3838617.39 VLBA_BR Br 48.13 119.68 251. -2112064.97 -3705356.51 4726813.79 VLBA_MK Mk 19.80 155.46 3764. -5464074.96 -2495249.12 2148296.84 BASELINE LENGTHS (km) Sc Hn Nl Fd La Pt Kp Ov Br Mk Sc 0 2853 3645 4143 4458 4579 4839 5460 5767 8611 Hn 2853 0 1611 3105 3006 3226 3623 3885 3657 7502 Nl 3645 1611 0 1654 1432 1663 2075 2328 2300 6156 Fd 4143 3105 1654 0 608 564 744 1508 2345 5134 La 4458 3006 1432 608 0 236 652 1088 1757 4970 Pt 4579 3226 1663 564 236 0 417 973 1806 4795 Kp 4839 3623 2075 744 652 417 0 845 1913 4466 Ov 5460 3885 2328 1508 1088 973 845 0 1214 4015 Br 5767 3657 2300 2345 1757 1806 1913 1214 0 4398 Mk 8611 7502 6156 5134 4970 4795 4466 4015 4398 0 TAPE INITIALIZATION and CONTROL INFORMATION: (See setup details later for times per pass.) Station Drives Head pos Tape len Density Start position Auto Auto (ft) Drive Head index Aloc Reverse VLBA_SC 2 14 18000 High 1 1 Yes Yes VLBA_HN 2 14 18000 High 1 1 Yes Yes VLBA_NL 2 14 18000 High 1 1 Yes Yes VLBA_FD 2 14 18000 High 1 1 Yes Yes VLBA_LA 2 14 18000 High 1 1 Yes Yes VLBA_PT 2 14 18000 High 1 1 Yes Yes VLBA_KP 2 14 18000 High 1 1 Yes Yes VLBA_OV 2 14 18000 High 1 1 Yes Yes VLBA_BR 2 14 18000 High 1 1 Yes Yes VLBA_MK 2 14 18000 High 1 1 Yes Yes EXPERIMENT SUMMARY: Number of input scans: 86 Number of scans scheduled: 86 Number of stations: 10 Number of sources input: 11 Number of setup files used: 46 Station summaries: Station Control Scans Scan Hours Tape hours Tapes Passes Readbacks VLBA_SC VLBA 86 5.02 4.61 1 13 6 VLBA_HN VLBA 86 5.02 4.61 1 13 6 VLBA_NL VLBA 86 5.02 4.61 1 13 6 VLBA_FD VLBA 86 5.02 4.61 1 13 6 VLBA_LA VLBA 86 5.02 4.61 1 13 6 VLBA_PT VLBA 86 5.02 4.61 1 13 6 VLBA_KP VLBA 86 5.02 4.61 1 13 6 VLBA_OV VLBA 86 5.02 4.61 1 13 6 VLBA_BR VLBA 86 5.02 4.61 1 13 6 VLBA_MK VLBA 86 5.02 4.61 1 13 6 Setup file: /home/aakash/kudre/VLBA/rfitest/90cm.set Matches group v5090n in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 1 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 1 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 325.00 326.00 327.00 328.00 329.00 330.00 331.00 332.00 BBC fr= 825.00 826.00 827.00 828.00 829.00 830.00 831.00 832.00 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/p325.set Matches group v5090n in /home/filehost/cwalker/sched/catalogs/freq.dat ****** Only 53.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. Setup group: 2 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 2 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 265.00 280.00 295.00 310.00 325.00 340.00 355.00 370.00 BBC fr= 765.00 780.00 795.00 810.00 825.00 840.00 855.00 870.00 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/50cm.set Matches group v5090w in /home/filehost/cwalker/sched/catalogs/freq.dat Wide 50 cm filter. Beware RFI. Some stations will saturate. ****** Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. Setup group: 3 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 50cm omit 50cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 3 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 545.00 560.00 575.00 590.00 605.00 620.00 635.00 650.00 BBC fr= 545.00 560.00 575.00 590.00 605.00 620.00 635.00 650.00 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/p605.set Matches group v5090w in /home/filehost/cwalker/sched/catalogs/freq.dat Wide 50 cm filter. Beware RFI. Some stations will saturate. ****** Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. Setup group: 4 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 50cm omit 50cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 4 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 545.00 560.00 575.00 590.00 605.00 620.00 635.00 650.00 BBC fr= 545.00 560.00 575.00 590.00 605.00 620.00 635.00 650.00 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/20cm.set Matches group v20cm_1 in /home/filehost/cwalker/sched/catalogs/freq.dat FD and KP filtered below 1330. SC filtered above 1440 Setup group: 5 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 2100.00 2100.00 2100.00 2100.00 2100.00 2100.00 2100.00 2100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 5 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1420.00 1420.00 1420.00 1420.00 1420.00 1420.00 1420.00 1420.00 BBC fr= 680.00 680.00 680.00 680.00 680.00 680.00 680.00 680.00 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/l2100.set Matches group v20cm_1 in /home/filehost/cwalker/sched/catalogs/freq.dat FD and KP filtered below 1330. SC filtered above 1440 Setup group: 6 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 2100.00 2100.00 2100.00 2100.00 2100.00 2100.00 2100.00 2100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 6 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1199.50 1214.50 1229.50 1244.50 1259.50 1274.50 1289.50 1304.50 BBC fr= 900.50 885.50 870.50 855.50 840.50 825.50 810.50 795.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 7 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1319.50 1334.50 1349.50 1364.50 1379.50 1394.50 1409.50 1424.50 BBC fr= 780.50 765.50 750.50 735.50 720.50 705.50 690.50 675.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 8 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1439.50 1454.50 1469.50 1484.50 1499.50 1514.50 1529.50 1544.50 BBC fr= 660.50 645.50 630.50 615.50 600.50 585.50 570.50 555.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/l2400.set Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 7 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 9 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1559.50 1574.50 1589.50 1604.50 1619.50 1634.50 1649.50 1664.50 BBC fr= 840.50 825.50 810.50 795.50 780.50 765.50 750.50 735.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 10 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1679.50 1694.50 1709.50 1724.50 1739.50 1754.50 1769.50 1784.50 BBC fr= 720.50 705.50 690.50 675.50 660.50 645.50 630.50 615.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/l2600.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 8 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 2600.00 2600.00 2600.00 2600.00 2600.00 2600.00 2600.00 2600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.6 15.4 The following frequency sets based on this setup were used. Frequency Set: 11 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1799.50 1814.50 1829.50 1844.50 1859.50 1874.50 1889.50 1904.50 BBC fr= 800.50 785.50 770.50 755.50 740.50 725.50 710.50 695.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/13cm.set Matches group v13cm_1 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 9 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 2900.00 2900.00 2900.00 2900.00 2900.00 2900.00 2900.00 2900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 2.9 15.4 The following frequency sets based on this setup were used. Frequency Set: 12 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2200.00 2200.00 2200.00 2200.00 2200.00 2200.00 2200.00 2200.00 BBC fr= 700.00 700.00 700.00 700.00 700.00 700.00 700.00 700.00 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/s2600.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 10 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 2600.00 2600.00 2600.00 2600.00 2600.00 2600.00 2600.00 2600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 2.6 15.4 The following frequency sets based on this setup were used. Frequency Set: 13 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1799.50 1814.50 1829.50 1844.50 1859.50 1874.50 1889.50 1904.50 BBC fr= 800.50 785.50 770.50 755.50 740.50 725.50 710.50 695.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 14 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 1919.50 1934.50 1949.50 1964.50 1979.50 1994.50 2009.50 2024.50 BBC fr= 680.50 665.50 650.50 635.50 620.50 605.50 590.50 575.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/s2900.set Matches group v13cm_1 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 11 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 2900.00 2900.00 2900.00 2900.00 2900.00 2900.00 2900.00 2900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 2.9 15.4 The following frequency sets based on this setup were used. Frequency Set: 15 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2039.50 2054.50 2069.50 2084.50 2099.50 2114.50 2129.50 2144.50 BBC fr= 860.50 845.50 830.50 815.50 800.50 785.50 770.50 755.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 16 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2159.50 2174.50 2189.50 2204.50 2219.50 2234.50 2249.50 2264.50 BBC fr= 740.50 725.50 710.50 695.50 680.50 665.50 650.50 635.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/s3100.set Matches group v13cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 12 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 17 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2279.50 2294.50 2309.50 2324.50 2339.50 2354.50 2369.50 2384.50 BBC fr= 820.50 805.50 790.50 775.50 760.50 745.50 730.50 715.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 18 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2399.50 2414.50 2429.50 2444.50 2459.50 2474.50 2489.50 2504.50 BBC fr= 700.50 685.50 670.50 655.50 640.50 625.50 610.50 595.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/s3400.set Matches group v13cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 13 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 3400.00 3400.00 3400.00 3400.00 3400.00 3400.00 3400.00 3400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 19 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2519.50 2534.50 2549.50 2564.50 2579.50 2594.50 2609.50 2624.50 BBC fr= 880.50 865.50 850.50 835.50 820.50 805.50 790.50 775.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 20 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2639.50 2654.50 2669.50 2684.50 2699.50 2714.50 2729.50 2744.50 BBC fr= 760.50 745.50 730.50 715.50 700.50 685.50 670.50 655.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/s3600.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 14 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 3600.00 3600.00 3600.00 3600.00 3600.00 3600.00 3600.00 3600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A A A A A A A A VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.6 15.4 The following frequency sets based on this setup were used. Frequency Set: 21 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2759.50 2774.50 2789.50 2804.50 2819.50 2834.50 2849.50 2864.50 BBC fr= 840.50 825.50 810.50 795.50 780.50 765.50 750.50 735.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 22 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 2879.50 2894.50 2909.50 2924.50 2939.50 2954.50 2969.50 2984.50 BBC fr= 720.50 705.50 690.50 675.50 660.50 645.50 630.50 615.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/6cm.set Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 15 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A A A A A A A A VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 23 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4800.50 4800.50 4800.50 4800.50 4800.50 4800.50 4800.50 4800.50 BBC fr= 700.50 700.50 700.50 700.50 700.50 700.50 700.50 700.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/c3600.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 16 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 3600.00 3600.00 3600.00 3600.00 3600.00 3600.00 3600.00 3600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A A A A A A A A VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 3.6 15.4 The following frequency sets based on this setup were used. Frequency Set: 24 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4259.50 4274.50 4289.50 4304.50 4319.50 4334.50 4349.50 4364.50 BBC fr= 659.50 674.50 689.50 704.50 719.50 734.50 749.50 764.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 25 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4379.50 4394.50 4409.50 4424.50 4439.50 4454.50 4469.50 4484.50 BBC fr= 779.50 794.50 809.50 824.50 839.50 854.50 869.50 884.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/c3900.set Matches group v6cm_1 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 17 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 3900.00 3900.00 3900.00 3900.00 3900.00 3900.00 3900.00 3900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A A A A A A A A VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 3.9 15.4 The following frequency sets based on this setup were used. Frequency Set: 26 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4499.50 4514.50 4529.50 4544.50 4559.50 4574.50 4589.50 4604.50 BBC fr= 599.50 614.50 629.50 644.50 659.50 674.50 689.50 704.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 27 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4619.50 4634.50 4649.50 4664.50 4679.50 4694.50 4709.50 4724.50 BBC fr= 719.50 734.50 749.50 764.50 779.50 794.50 809.50 824.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/c4100.set Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 18 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A A A A A A A A VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 28 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4739.50 4754.50 4769.50 4784.50 4799.50 4814.50 4829.50 4844.50 BBC fr= 639.50 654.50 669.50 684.50 699.50 714.50 729.50 744.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 29 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4859.50 4874.50 4889.50 4904.50 4919.50 4934.50 4949.50 4964.50 BBC fr= 759.50 774.50 789.50 804.50 819.50 834.50 849.50 864.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/c4400.set Matches group v6cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 19 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 4400.00 4400.00 4400.00 4400.00 4400.00 4400.00 4400.00 4400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A A A A A A A A VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 30 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 4979.50 4994.50 5009.50 5024.50 5039.50 5054.50 5069.50 5084.50 BBC fr= 579.50 594.50 609.50 624.50 639.50 654.50 669.50 684.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 31 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 5099.50 5114.50 5129.50 5144.50 5159.50 5174.50 5189.50 5204.50 BBC fr= 699.50 714.50 729.50 744.50 759.50 774.50 789.50 804.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 32 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 5219.50 5234.50 5249.50 5264.50 5279.50 5294.50 5309.50 5324.50 BBC fr= 819.50 834.50 849.50 864.50 879.50 894.50 909.50 924.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/4cm.set Matches group v4cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 20 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 33 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8400.50 8400.50 8400.50 8400.50 8400.50 8400.50 8400.50 8400.50 BBC fr= 800.50 800.50 800.50 800.50 800.50 800.50 800.50 800.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/x6900.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 21 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 6900.00 6900.00 6900.00 6900.00 6900.00 6900.00 6900.00 6900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 6.9 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 34 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 7499.50 7514.50 7529.50 7544.50 7559.50 7574.50 7589.50 7604.50 BBC fr= 599.50 614.50 629.50 644.50 659.50 674.50 689.50 704.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 35 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 7619.50 7634.50 7649.50 7664.50 7679.50 7694.50 7709.50 7724.50 BBC fr= 719.50 734.50 749.50 764.50 779.50 794.50 809.50 824.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 36 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 7739.50 7754.50 7769.50 7784.50 7799.50 7814.50 7829.50 7844.50 BBC fr= 839.50 854.50 869.50 884.50 899.50 914.50 929.50 944.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/x7100.set Matches group v4cm_1 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 22 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 7100.00 7100.00 7100.00 7100.00 7100.00 7100.00 7100.00 7100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.1 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 37 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 7859.50 7874.50 7889.50 7904.50 7919.50 7934.50 7949.50 7964.50 BBC fr= 759.50 774.50 789.50 804.50 819.50 834.50 849.50 864.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 38 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 7979.50 7994.50 8009.50 8024.50 8039.50 8054.50 8069.50 8084.50 BBC fr= 879.50 894.50 909.50 924.50 939.50 954.50 969.50 984.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/x7400.set Matches group v4cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 23 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 7400.00 7400.00 7400.00 7400.00 7400.00 7400.00 7400.00 7400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 39 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8099.50 8114.50 8129.50 8144.50 8159.50 8174.50 8189.50 8204.50 BBC fr= 699.50 714.50 729.50 744.50 759.50 774.50 789.50 804.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 40 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8219.50 8234.50 8249.50 8264.50 8279.50 8294.50 8309.50 8324.50 BBC fr= 819.50 834.50 849.50 864.50 879.50 894.50 909.50 924.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/x7600.set Matches group v4cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 24 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 41 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8339.50 8354.50 8369.50 8384.50 8399.50 8414.50 8429.50 8444.50 BBC fr= 739.50 754.50 769.50 784.50 799.50 814.50 829.50 844.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 42 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8459.50 8474.50 8489.50 8504.50 8519.50 8534.50 8549.50 8564.50 BBC fr= 859.50 874.50 889.50 904.50 919.50 934.50 949.50 964.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/x7900.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 25 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 7900.00 7900.00 7900.00 7900.00 7900.00 7900.00 7900.00 7900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.9 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 43 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8579.50 8594.50 8609.50 8624.50 8639.50 8654.50 8669.50 8684.50 BBC fr= 679.50 694.50 709.50 724.50 739.50 754.50 769.50 784.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 44 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8699.50 8714.50 8729.50 8744.50 8759.50 8774.50 8789.50 8804.50 BBC fr= 799.50 814.50 829.50 844.50 859.50 874.50 889.50 904.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/x8100.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 26 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 8100.00 8100.00 8100.00 8100.00 8100.00 8100.00 8100.00 8100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 8.1 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 45 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8819.50 8834.50 8849.50 8864.50 8879.50 8894.50 8909.50 8924.50 BBC fr= 719.50 734.50 749.50 764.50 779.50 794.50 809.50 824.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 46 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 8939.50 8954.50 8969.50 8984.50 8999.50 9014.50 9029.50 9044.50 BBC fr= 839.50 854.50 869.50 884.50 899.50 914.50 929.50 944.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/x8400.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 27 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 8400.00 8400.00 8400.00 8400.00 8400.00 8400.00 8400.00 8400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 4cm omit 4cm VLBA Synth= 8.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 47 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 9059.50 9074.50 9089.50 9104.50 9119.50 9134.50 9149.50 9164.50 BBC fr= 659.50 674.50 689.50 704.50 719.50 734.50 749.50 764.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/2cm.set Matches group v2cm_c5 in /home/filehost/cwalker/sched/catalogs/freq.dat Third 2cm filter Setup group: 28 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 14100.00 14100.00 14100.00 14100.00 14100.00 14100.00 14100.00 14100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.1 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 48 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14860.50 14860.50 14860.50 14860.50 14860.50 14860.50 14860.50 14860.50 BBC fr= 760.50 760.50 760.50 760.50 760.50 760.50 760.50 760.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u10900.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 29 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 10900.00 10900.00 10900.00 10900.00 10900.00 10900.00 10900.00 10900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 10.9 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 49 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 11499.50 11514.50 11529.50 11544.50 11559.50 11574.50 11589.50 11604.50 BBC fr= 599.50 614.50 629.50 644.50 659.50 674.50 689.50 704.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 50 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 11619.50 11634.50 11649.50 11664.50 11679.50 11694.50 11709.50 11724.50 BBC fr= 719.50 734.50 749.50 764.50 779.50 794.50 809.50 824.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 51 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 11739.50 11754.50 11769.50 11784.50 11799.50 11814.50 11829.50 11844.50 BBC fr= 839.50 854.50 869.50 884.50 899.50 914.50 929.50 944.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u11100.set Matches group v2cm_a1 in /home/filehost/cwalker/sched/catalogs/freq.dat First 2cm filter Setup group: 30 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 11100.00 11100.00 11100.00 11100.00 11100.00 11100.00 11100.00 11100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 11.1 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 52 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 11859.50 11874.50 11889.50 11904.50 11919.50 11934.50 11949.50 11964.50 BBC fr= 759.50 774.50 789.50 804.50 819.50 834.50 849.50 864.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 53 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 11979.50 11994.50 12009.50 12024.50 12039.50 12054.50 12069.50 12084.50 BBC fr= 879.50 894.50 909.50 924.50 939.50 954.50 969.50 984.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u11400.set Matches group v2cm_a1 in /home/filehost/cwalker/sched/catalogs/freq.dat First 2cm filter Setup group: 31 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 11400.00 11400.00 11400.00 11400.00 11400.00 11400.00 11400.00 11400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 11.4 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 54 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12099.50 12114.50 12129.50 12144.50 12159.50 12174.50 12189.50 12204.50 BBC fr= 699.50 714.50 729.50 744.50 759.50 774.50 789.50 804.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 55 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12219.50 12234.50 12249.50 12264.50 12279.50 12294.50 12309.50 12324.50 BBC fr= 819.50 834.50 849.50 864.50 879.50 894.50 909.50 924.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u11600.set Matches group v2cm_a3 in /home/filehost/cwalker/sched/catalogs/freq.dat First 2cm filter Setup group: 32 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 11600.00 11600.00 11600.00 11600.00 11600.00 11600.00 11600.00 11600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 11.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 56 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12339.50 12354.50 12369.50 12384.50 12399.50 12414.50 12429.50 12444.50 BBC fr= 739.50 754.50 769.50 784.50 799.50 814.50 829.50 844.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 57 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12459.50 12474.50 12489.50 12504.50 12519.50 12534.50 12549.50 12564.50 BBC fr= 859.50 874.50 889.50 904.50 919.50 934.50 949.50 964.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u11900.set Matches group v2cm_a4 in /home/filehost/cwalker/sched/catalogs/freq.dat First 2cm filter Setup group: 33 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 11900.00 11900.00 11900.00 11900.00 11900.00 11900.00 11900.00 11900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 11.9 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 58 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12579.50 12594.50 12609.50 12624.50 12639.50 12654.50 12669.50 12684.50 BBC fr= 679.50 694.50 709.50 724.50 739.50 754.50 769.50 784.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 59 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12699.50 12714.50 12729.50 12744.50 12759.50 12774.50 12789.50 12804.50 BBC fr= 799.50 814.50 829.50 844.50 859.50 874.50 889.50 904.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u12100.set Matches group v2cm_a5 in /home/filehost/cwalker/sched/catalogs/freq.dat First 2cm filter Setup group: 34 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 12100.00 12100.00 12100.00 12100.00 12100.00 12100.00 12100.00 12100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 12.1 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 60 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12819.50 12834.50 12849.50 12864.50 12879.50 12894.50 12909.50 12924.50 BBC fr= 719.50 734.50 749.50 764.50 779.50 794.50 809.50 824.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 61 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 12939.50 12954.50 12969.50 12984.50 12999.50 13014.50 13029.50 13044.50 BBC fr= 839.50 854.50 869.50 884.50 899.50 914.50 929.50 944.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u12400.set Matches group v2cm_b2 in /home/filehost/cwalker/sched/catalogs/freq.dat Second 2cm filter Setup group: 35 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 12400.00 12400.00 12400.00 12400.00 12400.00 12400.00 12400.00 12400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 12.4 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 62 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13059.50 13074.50 13089.50 13104.50 13119.50 13134.50 13149.50 13164.50 BBC fr= 659.50 674.50 689.50 704.50 719.50 734.50 749.50 764.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 63 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13179.50 13194.50 13209.50 13224.50 13239.50 13254.50 13269.50 13284.50 BBC fr= 779.50 794.50 809.50 824.50 839.50 854.50 869.50 884.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u12600.set Matches group v2cm_b3 in /home/filehost/cwalker/sched/catalogs/freq.dat Second 2cm filter Setup group: 36 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 12600.00 12600.00 12600.00 12600.00 12600.00 12600.00 12600.00 12600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 12.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 64 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13299.50 13314.50 13329.50 13344.50 13359.50 13374.50 13389.50 13404.50 BBC fr= 699.50 714.50 729.50 744.50 759.50 774.50 789.50 804.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 65 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13419.50 13434.50 13449.50 13464.50 13479.50 13494.50 13509.50 13524.50 BBC fr= 819.50 834.50 849.50 864.50 879.50 894.50 909.50 924.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u12900.set Matches group v2cm_b4 in /home/filehost/cwalker/sched/catalogs/freq.dat Second 2cm filter Setup group: 37 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 12900.00 12900.00 12900.00 12900.00 12900.00 12900.00 12900.00 12900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 12.9 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 66 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13539.50 13554.50 13569.50 13584.50 13599.50 13614.50 13629.50 13644.50 BBC fr= 639.50 654.50 669.50 684.50 699.50 714.50 729.50 744.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 67 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13659.50 13674.50 13689.50 13704.50 13719.50 13734.50 13749.50 13764.50 BBC fr= 759.50 774.50 789.50 804.50 819.50 834.50 849.50 864.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u13100.set Matches group v2cm_b5 in /home/filehost/cwalker/sched/catalogs/freq.dat Second 2cm filter Setup group: 38 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 13100.00 13100.00 13100.00 13100.00 13100.00 13100.00 13100.00 13100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 13.1 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 68 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13779.50 13794.50 13809.50 13824.50 13839.50 13854.50 13869.50 13884.50 BBC fr= 679.50 694.50 709.50 724.50 739.50 754.50 769.50 784.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 69 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 13899.50 13914.50 13929.50 13944.50 13959.50 13974.50 13989.50 14004.50 BBC fr= 799.50 814.50 829.50 844.50 859.50 874.50 889.50 904.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u13400.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 39 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 13400.00 13400.00 13400.00 13400.00 13400.00 13400.00 13400.00 13400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 13.4 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 70 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14019.50 14034.50 14049.50 14064.50 14079.50 14094.50 14109.50 14124.50 BBC fr= 619.50 634.50 649.50 664.50 679.50 694.50 709.50 724.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 71 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14139.50 14154.50 14169.50 14184.50 14199.50 14214.50 14229.50 14244.50 BBC fr= 739.50 754.50 769.50 784.50 799.50 814.50 829.50 844.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u13600.set Matches group v2cm_c3 in /home/filehost/cwalker/sched/catalogs/freq.dat Third 2cm filter Setup group: 40 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 13600.00 13600.00 13600.00 13600.00 13600.00 13600.00 13600.00 13600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 13.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 72 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14259.50 14274.50 14289.50 14304.50 14319.50 14334.50 14349.50 14364.50 BBC fr= 659.50 674.50 689.50 704.50 719.50 734.50 749.50 764.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 73 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14379.50 14394.50 14409.50 14424.50 14439.50 14454.50 14469.50 14484.50 BBC fr= 779.50 794.50 809.50 824.50 839.50 854.50 869.50 884.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u13900.set Matches group v2cm_c4 in /home/filehost/cwalker/sched/catalogs/freq.dat Third 2cm filter Setup group: 41 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 13900.00 13900.00 13900.00 13900.00 13900.00 13900.00 13900.00 13900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 13.9 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 74 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14499.50 14514.50 14529.50 14544.50 14559.50 14574.50 14589.50 14604.50 BBC fr= 599.50 614.50 629.50 644.50 659.50 674.50 689.50 704.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 75 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14619.50 14634.50 14649.50 14664.50 14679.50 14694.50 14709.50 14724.50 BBC fr= 719.50 734.50 749.50 764.50 779.50 794.50 809.50 824.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 76 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14739.50 14754.50 14769.50 14784.50 14799.50 14814.50 14829.50 14844.50 BBC fr= 839.50 854.50 869.50 884.50 899.50 914.50 929.50 944.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u14100.set Matches group v2cm_c5 in /home/filehost/cwalker/sched/catalogs/freq.dat Third 2cm filter Setup group: 42 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 14100.00 14100.00 14100.00 14100.00 14100.00 14100.00 14100.00 14100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.1 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 77 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14859.50 14874.50 14889.50 14904.50 14919.50 14934.50 14949.50 14964.50 BBC fr= 759.50 774.50 789.50 804.50 819.50 834.50 849.50 864.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 78 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 14979.50 14994.50 15009.50 15024.50 15039.50 15054.50 15069.50 15084.50 BBC fr= 879.50 894.50 909.50 924.50 939.50 954.50 969.50 984.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u14400.set Matches group v2cm_d2 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 43 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 14400.00 14400.00 14400.00 14400.00 14400.00 14400.00 14400.00 14400.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.4 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 79 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15099.50 15114.50 15129.50 15144.50 15159.50 15174.50 15189.50 15204.50 BBC fr= 699.50 714.50 729.50 744.50 759.50 774.50 789.50 804.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u14600.set Matches group v2cm_d3 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 44 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 80 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15219.50 15234.50 15249.50 15264.50 15279.50 15294.50 15309.50 15324.50 BBC fr= 619.50 634.50 649.50 664.50 679.50 694.50 709.50 724.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 81 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15339.50 15354.50 15369.50 15384.50 15399.50 15414.50 15429.50 15444.50 BBC fr= 739.50 754.50 769.50 784.50 799.50 814.50 829.50 844.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 82 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15459.50 15474.50 15489.50 15504.50 15519.50 15534.50 15549.50 15564.50 BBC fr= 859.50 874.50 889.50 904.50 919.50 934.50 949.50 964.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u14900.set Matches group v2cm_d4 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter. High IF freqs will be bad. Setup group: 45 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 14900.00 14900.00 14900.00 14900.00 14900.00 14900.00 14900.00 14900.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.9 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 83 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15579.50 15594.50 15609.50 15624.50 15639.50 15654.50 15669.50 15684.50 BBC fr= 679.50 694.50 709.50 724.50 739.50 754.50 769.50 784.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 84 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15699.50 15714.50 15729.50 15744.50 15759.50 15774.50 15789.50 15804.50 BBC fr= 799.50 814.50 829.50 844.50 859.50 874.50 889.50 904.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto Setup file: /home/aakash/kudre/VLBA/rfitest/u15100.set --- WARNING --- This group does not match an entry in the frequency catalog. Be very sure that it is correct. Setup group: 46 Station: VLBA Total bit rate: 256 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 8 Passes/head pos: 1 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 18000 ft, High density tapes is: 00:22:30 1st LO= 15100.00 15100.00 15100.00 15100.00 15100.00 15100.00 15100.00 15100.00 Net SB= U U U U U U U U Pol. = RCP RCP RCP RCP RCP RCP RCP RCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B B B B B B B B VLBA FE= omit 2cm omit 2cm VLBA Synth= 15.1 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 85 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15819.50 15834.50 15849.50 15864.50 15879.50 15894.50 15909.50 15924.50 BBC fr= 719.50 734.50 749.50 764.50 779.50 794.50 809.50 824.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 Frequency Set: 86 Based on FREQ, BW, and/or DOPPLER in schedule. Used pcal sets: 1 LO sum= 15939.50 15954.50 15969.50 15984.50 15999.50 16014.50 16029.50 16044.50 BBC fr= 839.50 854.50 869.50 884.50 899.50 914.50 929.50 944.50 Bandwd= 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = OFF PCALXB1= S1 S3 S5 S7 OFF OFF OFF OFF PCALXB2= S2 S4 S6 S8 OFF OFF OFF OFF PCALFR1= 0 0 0 0 0 0 0 0 PCALFR2= 0 0 0 0 0 0 0 0 Track assignments are: track1= 2, 10, 18, 26, 3, 11, 19, 27 barrel=roll_auto SUMMARY for experiment tr016 VLBA RFI survey: 90, 50, 20, 13, 6, 4, 2cm. Top item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) Bottom item is: End elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 38 is Thu 7 Feb 2002 MJD 52312 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Sc Hn Nl Fd La Pt Kp Ov Br Mk 38 17:00:00 90CM - 22 47 44 32 37 35 33 37 48 17 38 17:03:30 rfitest/90cm N 22 47 44 32 37 35 33 38 48 17 38 17:03:30 90CM - 22 47 44 32 37 35 33 38 48 17 38 17:07:00 rfitest/p325 - 22 47 44 32 37 36 33 38 48 17 38 17:07:00 50CM - 22 47 44 32 37 36 33 38 48 17 38 17:10:30 rfitest/50cm N 22 47 44 32 37 36 33 38 48 17 38 17:10:30 50CM - 22 47 44 32 37 36 33 38 48 17 38 17:14:00 rfitest/p605 - 22 47 44 32 37 36 33 38 48 17 38 17:14:00 20CM - 22 47 44 32 37 36 33 38 48 17 38 17:17:30 rfitest/20cm N 22 47 45 32 37 36 33 38 49 17 38 17:17:30 20CM - 22 47 45 32 37 36 33 38 49 17 38 17:21:00 fitest/l2100 - 22 47 45 33 37 36 33 38 49 17 38 17:21:00 20CM - 22 47 45 33 37 36 33 38 49 17 38 17:24:30 - - 22 47 45 33 38 36 33 38 49 18 38 17:24:30 20CM - 22 47 45 33 38 36 33 38 49 18 38 17:28:00 - - 22 47 45 33 38 36 33 38 49 18 38 17:28:00 20CM - 22 47 45 33 38 36 33 38 49 18 38 17:31:30 fitest/l2400 - 22 47 45 33 38 36 33 38 49 18 38 17:31:30 20CM - 22 47 45 33 38 36 33 38 49 18 38 17:35:00 - - 22 47 45 33 38 36 34 38 49 18 38 17:35:00 20CM - 22 47 45 33 38 36 34 38 49 18 38 17:38:30 fitest/l2600 - 22 47 45 33 38 36 34 38 49 18 38 17:38:30 13CM - 22 47 45 33 38 36 34 38 49 18 38 17:42:00 rfitest/13cm N 22 47 45 33 38 36 34 38 49 18 38 17:42:00 13CM - 22 47 45 33 38 36 34 38 49 18 38 17:45:30 fitest/s2600 - 22 47 45 33 38 36 34 38 49 18 38 17:45:30 13CM - 22 47 45 33 38 36 34 38 49 18 38 17:49:00 - - 22 47 45 33 38 36 34 39 49 18 38 17:49:00 13CM - 22 47 45 33 38 36 34 39 49 18 38 17:52:30 fitest/s2900 - 22 47 45 33 38 36 34 39 49 18 38 17:52:30 13CM - 22 47 45 33 38 36 34 39 49 18 38 17:56:00 - - 22 47 45 33 38 37 34 39 49 18 SUMMARY for experiment tr016 VLBA RFI survey: 90, 50, 20, 13, 6, 4, 2cm. Top item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) Bottom item is: End elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 38 is Thu 7 Feb 2002 MJD 52312 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Sc Hn Nl Fd La Pt Kp Ov Br Mk 38 17:56:00 13CM - 22 47 45 33 38 37 34 39 49 18 38 17:59:30 fitest/s3100 - 23 47 45 33 38 37 34 39 49 18 38 17:59:30 13CM - 23 47 45 33 38 37 34 39 49 18 38 18:03:00 - - 23 47 45 33 38 37 34 39 50 18 38 18:03:00 13CM - 23 47 45 33 38 37 34 39 50 18 38 18:06:30 fitest/s3400 - 23 48 45 33 38 37 34 39 50 18 38 18:06:30 13CM - 23 48 45 33 38 37 34 39 50 18 38 18:10:00 - - 23 48 45 33 38 37 34 39 50 18 38 18:10:00 13CM - 23 48 45 33 38 37 34 39 50 18 38 18:13:30 fitest/s3600 - 23 48 45 34 39 37 34 39 50 18 38 18:13:30 13CM - 23 48 45 34 39 37 34 39 50 18 38 18:17:00 - - 23 48 46 34 39 37 34 39 50 19 38 18:17:00 6CM - 23 48 46 34 39 37 34 39 50 19 38 18:20:30 /rfitest/6cm N 23 48 46 34 39 37 34 39 50 19 38 18:20:30 6CM - 23 48 46 34 39 37 34 39 50 19 38 18:24:00 fitest/c3600 - 23 48 46 34 39 37 35 39 50 19 38 18:24:00 6CM - 23 48 46 34 39 37 35 39 50 19 38 18:27:30 - - 23 48 46 34 39 37 35 39 50 19 38 18:27:30 6CM - 23 48 46 34 39 37 35 39 50 19 38 18:31:00 fitest/c3900 - 23 48 46 34 39 37 35 39 50 19 38 18:31:00 6CM - 23 48 46 34 39 37 35 39 50 19 38 18:34:30 - - 23 48 46 34 39 37 35 39 50 19 38 18:34:30 6CM - 23 48 46 34 39 37 35 39 50 19 38 18:38:00 fitest/c4100 - 23 48 46 34 39 37 35 40 50 19 38 18:38:00 6CM - 23 48 46 34 39 37 35 40 50 19 38 18:41:30 - - 23 48 46 34 39 37 35 40 50 19 38 18:41:30 6CM - 23 48 46 34 39 37 35 40 50 19 38 18:45:00 fitest/c4400 - 23 48 46 34 39 37 35 40 50 19 38 18:45:00 6CM - 23 48 46 34 39 37 35 40 50 19 38 18:48:30 - - 23 48 46 34 39 38 35 40 50 19 38 18:48:30 6CM - 23 48 46 34 39 38 35 40 50 19 38 18:52:00 - - 23 48 46 34 39 38 35 40 51 19 SUMMARY for experiment tr016 VLBA RFI survey: 90, 50, 20, 13, 6, 4, 2cm. Top item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) Bottom item is: End elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 38 is Thu 7 Feb 2002 MJD 52312 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Sc Hn Nl Fd La Pt Kp Ov Br Mk 38 18:52:00 4CMA - 23 48 46 34 39 38 35 40 51 19 38 18:55:30 /rfitest/4cm N 23 48 46 34 39 38 35 40 51 19 38 18:55:30 4CMA - 23 48 46 34 39 38 35 40 51 19 38 18:59:00 fitest/x6900 - 23 48 46 34 39 38 35 40 51 19 38 18:59:00 4CMA - 23 48 46 34 39 38 35 40 51 19 38 19:02:30 - - 23 48 46 34 39 38 35 40 51 20 38 19:02:30 4CMA - 23 48 46 34 39 38 35 40 51 20 38 19:06:00 - - 23 48 46 34 39 38 35 40 51 20 38 19:06:00 4CMA - 23 48 46 34 39 38 35 40 51 20 38 19:09:30 fitest/x7100 - 23 48 46 34 39 38 35 40 51 20 38 19:09:30 4CMA - 23 48 46 34 39 38 35 40 51 20 38 19:13:00 - - 23 48 46 35 40 38 35 40 51 20 38 19:13:00 4CMA - 23 48 46 35 40 38 35 40 51 20 38 19:16:30 fitest/x7400 - 23 48 46 35 40 38 35 40 51 20 38 19:16:30 4CMA - 23 48 46 35 40 38 35 40 51 20 38 19:20:00 - - 23 48 46 35 40 38 35 40 51 20 38 19:20:00 4CMB - 23 48 46 35 40 38 35 40 51 20 38 19:23:30 fitest/x7600 - 23 48 46 35 40 38 36 40 51 20 38 19:23:30 4CMB - 23 48 46 35 40 38 36 40 51 20 38 19:27:00 - - 23 48 46 35 40 38 36 40 51 20 38 19:27:00 4CMB - 23 48 46 35 40 38 36 40 51 20 38 19:30:30 fitest/x7900 - 23 48 46 35 40 38 36 40 51 20 38 19:30:30 4CMB - 23 48 46 35 40 38 36 40 51 20 38 19:34:00 - - 23 48 46 35 40 38 36 41 51 20 38 19:34:00 4CMB - 23 48 46 35 40 38 36 41 51 20 38 19:37:30 fitest/x8100 - 23 48 46 35 40 38 36 41 51 20 38 19:37:30 4CMB - 23 48 46 35 40 38 36 41 51 20 38 19:41:00 - - 23 48 46 35 40 38 36 41 51 20 38 19:41:00 4CMB - 23 48 46 35 40 38 36 41 51 20 38 19:44:30 fitest/x8400 - 23 48 47 35 40 38 36 41 51 20 38 19:44:30 2CMA - 23 48 47 35 40 38 36 41 51 20 38 19:48:00 /rfitest/2cm N 23 48 47 35 40 38 36 41 52 21 SUMMARY for experiment tr016 VLBA RFI survey: 90, 50, 20, 13, 6, 4, 2cm. Top item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) Bottom item is: End elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 38 is Thu 7 Feb 2002 MJD 52312 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Sc Hn Nl Fd La Pt Kp Ov Br Mk 38 19:48:00 2CMA - 23 48 47 35 40 38 36 41 52 21 38 19:51:30 itest/u10900 - 23 48 47 35 40 38 36 41 52 21 38 19:51:30 2CMA - 23 48 47 35 40 38 36 41 52 21 38 19:55:00 - - 23 48 47 35 40 39 36 41 52 21 38 19:55:00 2CMA - 23 48 47 35 40 39 36 41 52 21 38 19:58:30 - - 23 48 47 35 40 39 36 41 52 21 38 19:58:30 2CMA - 23 48 47 35 40 39 36 41 52 21 38 20:02:00 itest/u11100 - 23 48 47 35 40 39 36 41 52 21 38 20:02:00 2CMA - 23 48 47 35 40 39 36 41 52 21 38 20:05:30 - - 23 48 47 35 40 39 36 41 52 21 38 20:05:30 2CMA - 23 48 47 35 40 39 36 41 52 21 38 20:09:00 itest/u11400 - 23 48 47 35 40 39 36 41 52 21 38 20:09:00 2CMA - 23 48 47 35 40 39 36 41 52 21 38 20:12:30 - - 23 48 47 35 40 39 36 41 52 21 38 20:12:30 2CMA - 23 48 47 35 40 39 36 41 52 21 38 20:16:00 itest/u11600 - 23 48 47 35 40 39 36 41 52 21 38 20:16:00 2CMA - 23 48 47 35 40 39 36 41 52 21 38 20:19:30 - - 22 48 47 35 40 39 36 41 52 21 38 20:19:30 2CMA - 22 48 47 35 40 39 36 41 52 21 38 20:23:00 itest/u11900 - 22 48 47 35 40 39 36 41 52 21 38 20:23:00 2CMB - 22 48 47 35 40 39 36 41 52 21 38 20:26:30 - - 22 48 47 35 40 39 36 41 52 21 38 20:26:30 2CMB - 22 48 47 35 40 39 36 41 52 21 38 20:30:00 itest/u12100 - 22 48 47 35 40 39 36 41 52 21 38 20:30:00 2CMB - 22 48 47 35 40 39 36 41 52 21 38 20:33:30 - - 22 48 47 35 40 39 36 41 52 21 38 20:33:30 2CMB - 22 48 47 35 40 39 36 41 52 21 38 20:37:00 itest/u12400 - 22 48 47 35 40 39 36 41 52 22 38 20:37:00 2CMB - 22 48 47 35 40 39 36 41 52 22 38 20:40:30 - - 22 48 47 35 40 39 36 41 52 22 38 20:40:30 2CMB - 22 48 47 35 40 39 36 41 52 22 38 20:44:00 itest/u12600 - 22 48 47 35 41 39 37 42 52 22 SUMMARY for experiment tr016 VLBA RFI survey: 90, 50, 20, 13, 6, 4, 2cm. Top item is: Start elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) Bottom item is: End elevation, flag (D=>Down, H=>Below Horizon, t=>Tape Change.) TYPE top: -=> normal scan, P=>Pointing or Ta; bottom: -=>recording, N=>not recording. Day 38 is Thu 7 Feb 2002 MJD 52312 DAY START UT SOURCE TYPE STATIONS t => tape change STOP UT Sc Hn Nl Fd La Pt Kp Ov Br Mk 38 20:44:00 2CMB - 22 48 47 35 41 39 37 42 52 22 38 20:47:30 itest/u12600 - 22 48 47 35 41 39 37 42 52 22 38 20:47:30 2CMB - 22 48 47 35 41 39 37 42 52 22 38 20:51:00 itest/u12900 - 22 48 47 35 41 39 37 42 52 22 38 20:51:00 2CMB - 22 48 47 35 41 39 37 42 52 22 38 20:54:30 - - 22 48 47 35 41 39 37 42 52 22 38 20:54:30 2CMB - 22 48 47 35 41 39 37 42 52 22 38 20:58:00 itest/u13100 - 22 48 47 36 41 39 37 42 53 22 38 20:58:00 2CMC - 22 48 47 36 41 39 37 42 53 22 38 21:01:30 - - 22 48 47 36 41 39 37 42 53 22 38 21:01:30 2CMC - 22 48 47 36 41 39 37 42 53 22 38 21:05:00 itest/u13400 - 22 48 47 36 41 39 37 42 53 22 38 21:05:00 2CMC - 22 48 47 36 41 39 37 42 53 22 38 21:08:30 - - 22 47 47 36 41 39 37 42 53 22 38 21:08:30 2CMC - 22 47 47 36 41 39 37 42 53 22 38 21:12:00 itest/u13600 - 22 47 47 36 41 39 37 42 53 22 38 21:12:00 2CMC - 22 47 47 36 41 39 37 42 53 22 38 21:15