Welcome to program SCHED. Version: 7.00 Development late 2006 The manual is at http://www.aoc.nrao.edu/~cwalker/sched/sched/sched.html Unix users should set $SCHED to the base area where SCHED is installed. Most run time messages will be in sched.runlog Some useful commands to give now if running interactively: SCHedule= : Specify input file. PLOT : Invokes uv, xy, rd, and uptime plotting. FREQLIST=lowF,highF : Make frequency list (MHz). Then exit. EXIT : Leave program. / : End of inputs - run program (or EXIT). SRREAD: Reading source catalog: Program_input SRREAD: Please convert source catalog from use of EPOCH to EQUINOX. STREAD: Reading station catalog: /home/arana/cwalker/sched/catalogs/stations.dat STREAD: Will read locations file /home/arana/cwalker/sched/catalogs/locations.dat SCHIN: Found 86 input scans. TPINI: Using default tape initialization information. SCHIN: * Automatic tape allocation requested at: Pt Kp Ov Br Mk RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/90cm.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/p325.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/50cm.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/p605.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/20cm.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/l2100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/l2400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/l2600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/13cm.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/s2600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/s2900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/s3100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/s3400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/s3600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/6cm.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/c3600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/c3900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/c4100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/c4400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/4cm.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/x6900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/x7100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/x7400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/x7600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/x7900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/x8100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/x8400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/2cm.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u10900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u11100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u11400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u11600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u11900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u12100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u12400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u12600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u12900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u13100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u13400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u13600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u13900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u14100.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u14400.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u14600.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u14900.set RDSET: Reading setup file: /home/aakash/kudre/VLBA/rfitest/u15100.set GETFREQ: Reading frequency file: /home/arana/cwalker/sched/catalogs/freq.dat SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p325.set Station VLBA_PT Only 53.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p325.set Station VLBA_KP Only 53.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p325.set Station VLBA_OV Only 53.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p325.set Station VLBA_BR Only 53.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p325.set Station VLBA_MK Only 53.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/50cm.set Station VLBA_PT Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/50cm.set Station VLBA_KP Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/50cm.set Station VLBA_OV Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/50cm.set Station VLBA_BR Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/50cm.set Station VLBA_MK Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p605.set Station VLBA_PT Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p605.set Station VLBA_KP Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p605.set Station VLBA_OV Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p605.set Station VLBA_BR Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/p605.set Station VLBA_MK Only 48.00 of 128.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/l2600.set Station VLBA_PT WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T T T T v20cm_2 2 1 T F T T T T T T v20cm_2 3 1 T F T T T T T T v20cm_2 4 1 T F T T T T T T v20cm_2 5 1 T F T T T T F T v20cm_2 6 1 T F T T T T F T v20cm_2 7 1 T F T T T T F T v20cm_2 8 1 T F T T T T F T vsx_11 8 1 T F T T T F T T vsx_12 8 1 T F T T T F T T vsx_13 8 1 T F T T T F T T vsx_14 8 1 T F T T T F T T vsx_1w 8 1 T F T T T F T T vsx_2w 8 1 T F T T T F T T vsx_5w 8 1 T F T T T F T T vsx_6w 8 1 T F T T T F T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/l2600.set Station VLBA_KP WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T T T T v20cm_2 2 1 T F T T T T T T v20cm_2 3 1 T F T T T T T T v20cm_2 4 1 T F T T T T T T v20cm_2 5 1 T F T T T T F T v20cm_2 6 1 T F T T T T F T v20cm_2 7 1 T F T T T T F T v20cm_2 8 1 T F T T T T F T vsx_11 8 1 T F T T T F T T vsx_12 8 1 T F T T T F T T vsx_13 8 1 T F T T T F T T vsx_14 8 1 T F T T T F T T vsx_1w 8 1 T F T T T F T T vsx_2w 8 1 T F T T T F T T vsx_5w 8 1 T F T T T F T T vsx_6w 8 1 T F T T T F T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/l2600.set Station VLBA_OV WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T T T T v20cm_2 2 1 T F T T T T T T v20cm_2 3 1 T F T T T T T T v20cm_2 4 1 T F T T T T T T v20cm_2 5 1 T F T T T T F T v20cm_2 6 1 T F T T T T F T v20cm_2 7 1 T F T T T T F T v20cm_2 8 1 T F T T T T F T vsx_11 8 1 T F T T T F T T vsx_12 8 1 T F T T T F T T vsx_13 8 1 T F T T T F T T vsx_14 8 1 T F T T T F T T vsx_1w 8 1 T F T T T F T T vsx_2w 8 1 T F T T T F T T vsx_5w 8 1 T F T T T F T T vsx_6w 8 1 T F T T T F T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/l2600.set Station VLBA_BR WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T T T T v20cm_2 2 1 T F T T T T T T v20cm_2 3 1 T F T T T T T T v20cm_2 4 1 T F T T T T T T v20cm_2 5 1 T F T T T T F T v20cm_2 6 1 T F T T T T F T v20cm_2 7 1 T F T T T T F T v20cm_2 8 1 T F T T T T F T vsx_11 8 1 T F T T T F T T vsx_12 8 1 T F T T T F T T vsx_13 8 1 T F T T T F T T vsx_14 8 1 T F T T T F T T vsx_1w 8 1 T F T T T F T T vsx_2w 8 1 T F T T T F T T vsx_5w 8 1 T F T T T F T T vsx_6w 8 1 T F T T T F T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/l2600.set Station VLBA_MK WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T T T T v20cm_2 2 1 T F T T T T T T v20cm_2 3 1 T F T T T T T T v20cm_2 4 1 T F T T T T T T v20cm_2 5 1 T F T T T T F T v20cm_2 6 1 T F T T T T F T v20cm_2 7 1 T F T T T T F T v20cm_2 8 1 T F T T T T F T vsx_11 8 1 T F T T T F T T vsx_12 8 1 T F T T T F T T vsx_13 8 1 T F T T T F T T vsx_14 8 1 T F T T T F T T vsx_1w 8 1 T F T T T F T T vsx_2w 8 1 T F T T T F T T vsx_5w 8 1 T F T T T F T T vsx_6w 8 1 T F T T T F T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s2600.set Station VLBA_PT WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T F T T v20cm_2 2 1 T F T T T F T T v20cm_2 3 1 T F T T T F T T v20cm_2 4 1 T F T T T F T T v20cm_2 5 1 T F T T T F F T v20cm_2 6 1 T F T T T F F T v20cm_2 7 1 T F T T T F F T v20cm_2 8 1 T F T T T F F T vsx_11 1 1 T F T T T T F T vsx_11 2 1 T F T T T T F T vsx_11 3 1 T F T T T T F T vsx_11 4 1 T F T T T T F T vsx_11 5 1 T F T T T T F T vsx_11 6 1 T F T T T T F T vsx_11 7 1 T F T T T T F T vsx_11 8 1 T F T T T T T T vsx_12 1 1 T F T T T T F T vsx_12 2 1 T F T T T T F T vsx_12 3 1 T F T T T T F T vsx_12 4 1 T F T T T T F T vsx_12 5 1 T F T T T T F T vsx_12 6 1 T F T T T T F T vsx_12 7 1 T F T T T T F T vsx_12 8 1 T F T T T T T T vsx_13 1 1 T F T T T T F T vsx_13 2 1 T F T T T T F T vsx_13 3 1 T F T T T T F T vsx_13 4 1 T F T T T T F T vsx_13 5 1 T F T T T T F T vsx_13 6 1 T F T T T T F T vsx_13 7 1 T F T T T T F T vsx_13 8 1 T F T T T T T T vsx_14 1 1 T F T T T T F T vsx_14 2 1 T F T T T T F T vsx_14 3 1 T F T T T T F T vsx_14 4 1 T F T T T T F T vsx_14 5 1 T F T T T T F T vsx_14 6 1 T F T T T T F T vsx_14 7 1 T F T T T T F T vsx_14 8 1 T F T T T T T T vsx_1w 1 1 T F T T T T F T vsx_1w 2 1 T F T T T T F T vsx_1w 3 1 T F T T T T F T vsx_1w 4 1 T F T T T T F T vsx_1w 5 1 T F T T T T F T vsx_1w 6 1 T F T T T T F T vsx_1w 7 1 T F T T T T F T vsx_1w 8 1 T F T T T T T T vsx_2w 1 1 T F T T T T F T vsx_2w 2 1 T F T T T T F T vsx_2w 3 1 T F T T T T F T vsx_2w 4 1 T F T T T T F T vsx_2w 5 1 T F T T T T F T vsx_2w 6 1 T F T T T T F T vsx_2w 7 1 T F T T T T F T vsx_2w 8 1 T F T T T T T T vsx_5w 1 1 T F T T T T F T vsx_5w 2 1 T F T T T T F T vsx_5w 3 1 T F T T T T F T vsx_5w 4 1 T F T T T T F T vsx_5w 5 1 T F T T T T F T vsx_5w 6 1 T F T T T T F T vsx_5w 7 1 T F T T T T F T vsx_5w 8 1 T F T T T T T T vsx_6w 1 1 T F T T T T F T vsx_6w 2 1 T F T T T T F T vsx_6w 3 1 T F T T T T F T vsx_6w 4 1 T F T T T T F T vsx_6w 5 1 T F T T T T F T vsx_6w 6 1 T F T T T T F T vsx_6w 7 1 T F T T T T F T vsx_6w 8 1 T F T T T T T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s2600.set Station VLBA_KP WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T F T T v20cm_2 2 1 T F T T T F T T v20cm_2 3 1 T F T T T F T T v20cm_2 4 1 T F T T T F T T v20cm_2 5 1 T F T T T F F T v20cm_2 6 1 T F T T T F F T v20cm_2 7 1 T F T T T F F T v20cm_2 8 1 T F T T T F F T vsx_11 1 1 T F T T T T F T vsx_11 2 1 T F T T T T F T vsx_11 3 1 T F T T T T F T vsx_11 4 1 T F T T T T F T vsx_11 5 1 T F T T T T F T vsx_11 6 1 T F T T T T F T vsx_11 7 1 T F T T T T F T vsx_11 8 1 T F T T T T T T vsx_12 1 1 T F T T T T F T vsx_12 2 1 T F T T T T F T vsx_12 3 1 T F T T T T F T vsx_12 4 1 T F T T T T F T vsx_12 5 1 T F T T T T F T vsx_12 6 1 T F T T T T F T vsx_12 7 1 T F T T T T F T vsx_12 8 1 T F T T T T T T vsx_13 1 1 T F T T T T F T vsx_13 2 1 T F T T T T F T vsx_13 3 1 T F T T T T F T vsx_13 4 1 T F T T T T F T vsx_13 5 1 T F T T T T F T vsx_13 6 1 T F T T T T F T vsx_13 7 1 T F T T T T F T vsx_13 8 1 T F T T T T T T vsx_14 1 1 T F T T T T F T vsx_14 2 1 T F T T T T F T vsx_14 3 1 T F T T T T F T vsx_14 4 1 T F T T T T F T vsx_14 5 1 T F T T T T F T vsx_14 6 1 T F T T T T F T vsx_14 7 1 T F T T T T F T vsx_14 8 1 T F T T T T T T vsx_1w 1 1 T F T T T T F T vsx_1w 2 1 T F T T T T F T vsx_1w 3 1 T F T T T T F T vsx_1w 4 1 T F T T T T F T vsx_1w 5 1 T F T T T T F T vsx_1w 6 1 T F T T T T F T vsx_1w 7 1 T F T T T T F T vsx_1w 8 1 T F T T T T T T vsx_2w 1 1 T F T T T T F T vsx_2w 2 1 T F T T T T F T vsx_2w 3 1 T F T T T T F T vsx_2w 4 1 T F T T T T F T vsx_2w 5 1 T F T T T T F T vsx_2w 6 1 T F T T T T F T vsx_2w 7 1 T F T T T T F T vsx_2w 8 1 T F T T T T T T vsx_5w 1 1 T F T T T T F T vsx_5w 2 1 T F T T T T F T vsx_5w 3 1 T F T T T T F T vsx_5w 4 1 T F T T T T F T vsx_5w 5 1 T F T T T T F T vsx_5w 6 1 T F T T T T F T vsx_5w 7 1 T F T T T T F T vsx_5w 8 1 T F T T T T T T vsx_6w 1 1 T F T T T T F T vsx_6w 2 1 T F T T T T F T vsx_6w 3 1 T F T T T T F T vsx_6w 4 1 T F T T T T F T vsx_6w 5 1 T F T T T T F T vsx_6w 6 1 T F T T T T F T vsx_6w 7 1 T F T T T T F T vsx_6w 8 1 T F T T T T T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s2600.set Station VLBA_OV WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T F T T v20cm_2 2 1 T F T T T F T T v20cm_2 3 1 T F T T T F T T v20cm_2 4 1 T F T T T F T T v20cm_2 5 1 T F T T T F F T v20cm_2 6 1 T F T T T F F T v20cm_2 7 1 T F T T T F F T v20cm_2 8 1 T F T T T F F T vsx_11 1 1 T F T T T T F T vsx_11 2 1 T F T T T T F T vsx_11 3 1 T F T T T T F T vsx_11 4 1 T F T T T T F T vsx_11 5 1 T F T T T T F T vsx_11 6 1 T F T T T T F T vsx_11 7 1 T F T T T T F T vsx_11 8 1 T F T T T T T T vsx_12 1 1 T F T T T T F T vsx_12 2 1 T F T T T T F T vsx_12 3 1 T F T T T T F T vsx_12 4 1 T F T T T T F T vsx_12 5 1 T F T T T T F T vsx_12 6 1 T F T T T T F T vsx_12 7 1 T F T T T T F T vsx_12 8 1 T F T T T T T T vsx_13 1 1 T F T T T T F T vsx_13 2 1 T F T T T T F T vsx_13 3 1 T F T T T T F T vsx_13 4 1 T F T T T T F T vsx_13 5 1 T F T T T T F T vsx_13 6 1 T F T T T T F T vsx_13 7 1 T F T T T T F T vsx_13 8 1 T F T T T T T T vsx_14 1 1 T F T T T T F T vsx_14 2 1 T F T T T T F T vsx_14 3 1 T F T T T T F T vsx_14 4 1 T F T T T T F T vsx_14 5 1 T F T T T T F T vsx_14 6 1 T F T T T T F T vsx_14 7 1 T F T T T T F T vsx_14 8 1 T F T T T T T T vsx_1w 1 1 T F T T T T F T vsx_1w 2 1 T F T T T T F T vsx_1w 3 1 T F T T T T F T vsx_1w 4 1 T F T T T T F T vsx_1w 5 1 T F T T T T F T vsx_1w 6 1 T F T T T T F T vsx_1w 7 1 T F T T T T F T vsx_1w 8 1 T F T T T T T T vsx_2w 1 1 T F T T T T F T vsx_2w 2 1 T F T T T T F T vsx_2w 3 1 T F T T T T F T vsx_2w 4 1 T F T T T T F T vsx_2w 5 1 T F T T T T F T vsx_2w 6 1 T F T T T T F T vsx_2w 7 1 T F T T T T F T vsx_2w 8 1 T F T T T T T T vsx_5w 1 1 T F T T T T F T vsx_5w 2 1 T F T T T T F T vsx_5w 3 1 T F T T T T F T vsx_5w 4 1 T F T T T T F T vsx_5w 5 1 T F T T T T F T vsx_5w 6 1 T F T T T T F T vsx_5w 7 1 T F T T T T F T vsx_5w 8 1 T F T T T T T T vsx_6w 1 1 T F T T T T F T vsx_6w 2 1 T F T T T T F T vsx_6w 3 1 T F T T T T F T vsx_6w 4 1 T F T T T T F T vsx_6w 5 1 T F T T T T F T vsx_6w 6 1 T F T T T T F T vsx_6w 7 1 T F T T T T F T vsx_6w 8 1 T F T T T T T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s2600.set Station VLBA_BR WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T F T T v20cm_2 2 1 T F T T T F T T v20cm_2 3 1 T F T T T F T T v20cm_2 4 1 T F T T T F T T v20cm_2 5 1 T F T T T F F T v20cm_2 6 1 T F T T T F F T v20cm_2 7 1 T F T T T F F T v20cm_2 8 1 T F T T T F F T vsx_11 1 1 T F T T T T F T vsx_11 2 1 T F T T T T F T vsx_11 3 1 T F T T T T F T vsx_11 4 1 T F T T T T F T vsx_11 5 1 T F T T T T F T vsx_11 6 1 T F T T T T F T vsx_11 7 1 T F T T T T F T vsx_11 8 1 T F T T T T T T vsx_12 1 1 T F T T T T F T vsx_12 2 1 T F T T T T F T vsx_12 3 1 T F T T T T F T vsx_12 4 1 T F T T T T F T vsx_12 5 1 T F T T T T F T vsx_12 6 1 T F T T T T F T vsx_12 7 1 T F T T T T F T vsx_12 8 1 T F T T T T T T vsx_13 1 1 T F T T T T F T vsx_13 2 1 T F T T T T F T vsx_13 3 1 T F T T T T F T vsx_13 4 1 T F T T T T F T vsx_13 5 1 T F T T T T F T vsx_13 6 1 T F T T T T F T vsx_13 7 1 T F T T T T F T vsx_13 8 1 T F T T T T T T vsx_14 1 1 T F T T T T F T vsx_14 2 1 T F T T T T F T vsx_14 3 1 T F T T T T F T vsx_14 4 1 T F T T T T F T vsx_14 5 1 T F T T T T F T vsx_14 6 1 T F T T T T F T vsx_14 7 1 T F T T T T F T vsx_14 8 1 T F T T T T T T vsx_1w 1 1 T F T T T T F T vsx_1w 2 1 T F T T T T F T vsx_1w 3 1 T F T T T T F T vsx_1w 4 1 T F T T T T F T vsx_1w 5 1 T F T T T T F T vsx_1w 6 1 T F T T T T F T vsx_1w 7 1 T F T T T T F T vsx_1w 8 1 T F T T T T T T vsx_2w 1 1 T F T T T T F T vsx_2w 2 1 T F T T T T F T vsx_2w 3 1 T F T T T T F T vsx_2w 4 1 T F T T T T F T vsx_2w 5 1 T F T T T T F T vsx_2w 6 1 T F T T T T F T vsx_2w 7 1 T F T T T T F T vsx_2w 8 1 T F T T T T T T vsx_5w 1 1 T F T T T T F T vsx_5w 2 1 T F T T T T F T vsx_5w 3 1 T F T T T T F T vsx_5w 4 1 T F T T T T F T vsx_5w 5 1 T F T T T T F T vsx_5w 6 1 T F T T T T F T vsx_5w 7 1 T F T T T T F T vsx_5w 8 1 T F T T T T T T vsx_6w 1 1 T F T T T T F T vsx_6w 2 1 T F T T T T F T vsx_6w 3 1 T F T T T T F T vsx_6w 4 1 T F T T T T F T vsx_6w 5 1 T F T T T T F T vsx_6w 6 1 T F T T T T F T vsx_6w 7 1 T F T T T T F T vsx_6w 8 1 T F T T T T T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s2600.set Station VLBA_MK WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v20cm_2 1 1 T F T T T F T T v20cm_2 2 1 T F T T T F T T v20cm_2 3 1 T F T T T F T T v20cm_2 4 1 T F T T T F T T v20cm_2 5 1 T F T T T F F T v20cm_2 6 1 T F T T T F F T v20cm_2 7 1 T F T T T F F T v20cm_2 8 1 T F T T T F F T vsx_11 1 1 T F T T T T F T vsx_11 2 1 T F T T T T F T vsx_11 3 1 T F T T T T F T vsx_11 4 1 T F T T T T F T vsx_11 5 1 T F T T T T F T vsx_11 6 1 T F T T T T F T vsx_11 7 1 T F T T T T F T vsx_11 8 1 T F T T T T T T vsx_12 1 1 T F T T T T F T vsx_12 2 1 T F T T T T F T vsx_12 3 1 T F T T T T F T vsx_12 4 1 T F T T T T F T vsx_12 5 1 T F T T T T F T vsx_12 6 1 T F T T T T F T vsx_12 7 1 T F T T T T F T vsx_12 8 1 T F T T T T T T vsx_13 1 1 T F T T T T F T vsx_13 2 1 T F T T T T F T vsx_13 3 1 T F T T T T F T vsx_13 4 1 T F T T T T F T vsx_13 5 1 T F T T T T F T vsx_13 6 1 T F T T T T F T vsx_13 7 1 T F T T T T F T vsx_13 8 1 T F T T T T T T vsx_14 1 1 T F T T T T F T vsx_14 2 1 T F T T T T F T vsx_14 3 1 T F T T T T F T vsx_14 4 1 T F T T T T F T vsx_14 5 1 T F T T T T F T vsx_14 6 1 T F T T T T F T vsx_14 7 1 T F T T T T F T vsx_14 8 1 T F T T T T T T vsx_1w 1 1 T F T T T T F T vsx_1w 2 1 T F T T T T F T vsx_1w 3 1 T F T T T T F T vsx_1w 4 1 T F T T T T F T vsx_1w 5 1 T F T T T T F T vsx_1w 6 1 T F T T T T F T vsx_1w 7 1 T F T T T T F T vsx_1w 8 1 T F T T T T T T vsx_2w 1 1 T F T T T T F T vsx_2w 2 1 T F T T T T F T vsx_2w 3 1 T F T T T T F T vsx_2w 4 1 T F T T T T F T vsx_2w 5 1 T F T T T T F T vsx_2w 6 1 T F T T T T F T vsx_2w 7 1 T F T T T T F T vsx_2w 8 1 T F T T T T T T vsx_5w 1 1 T F T T T T F T vsx_5w 2 1 T F T T T T F T vsx_5w 3 1 T F T T T T F T vsx_5w 4 1 T F T T T T F T vsx_5w 5 1 T F T T T T F T vsx_5w 6 1 T F T T T T F T vsx_5w 7 1 T F T T T T F T vsx_5w 8 1 T F T T T T T T vsx_6w 1 1 T F T T T T F T vsx_6w 2 1 T F T T T T F T vsx_6w 3 1 T F T T T T F T vsx_6w 4 1 T F T T T T F T vsx_6w 5 1 T F T T T T F T vsx_6w 6 1 T F T T T T F T vsx_6w 7 1 T F T T T T F T vsx_6w 8 1 T F T T T T T T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s3600.set Station VLBA_PT WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v13cm_3 1 1 T F T T T T T T v13cm_3 2 1 T F T T T T T T v13cm_3 3 1 T F T T T T T T v13cm_3 4 1 T F T T T T T T v13cm_3 5 1 T F T T T T T T v13cm_3 6 1 T F T T T T T T v13cm_3 7 1 T F T T T T F T v13cm_3 8 1 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s3600.set Station VLBA_KP WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v13cm_3 1 1 T F T T T T T T v13cm_3 2 1 T F T T T T T T v13cm_3 3 1 T F T T T T T T v13cm_3 4 1 T F T T T T T T v13cm_3 5 1 T F T T T T T T v13cm_3 6 1 T F T T T T T T v13cm_3 7 1 T F T T T T F T v13cm_3 8 1 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s3600.set Station VLBA_OV WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v13cm_3 1 1 T F T T T T T T v13cm_3 2 1 T F T T T T T T v13cm_3 3 1 T F T T T T T T v13cm_3 4 1 T F T T T T T T v13cm_3 5 1 T F T T T T T T v13cm_3 6 1 T F T T T T T T v13cm_3 7 1 T F T T T T F T v13cm_3 8 1 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s3600.set Station VLBA_BR WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v13cm_3 1 1 T F T T T T T T v13cm_3 2 1 T F T T T T T T v13cm_3 3 1 T F T T T T T T v13cm_3 4 1 T F T T T T T T v13cm_3 5 1 T F T T T T T T v13cm_3 6 1 T F T T T T T T v13cm_3 7 1 T F T T T T F T v13cm_3 8 1 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/s3600.set Station VLBA_MK WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v13cm_3 1 1 T F T T T T T T v13cm_3 2 1 T F T T T T T T v13cm_3 3 1 T F T T T T T T v13cm_3 4 1 T F T T T T T T v13cm_3 5 1 T F T T T T T T v13cm_3 6 1 T F T T T T T T v13cm_3 7 1 T F T T T T F T v13cm_3 8 1 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/c3600.set Station VLBA_PT WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/c3600.set Station VLBA_KP WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/c3600.set Station VLBA_OV WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/c3600.set Station VLBA_BR WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/c3600.set Station VLBA_MK WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x6900.set Station VLBA_PT WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x6900.set Station VLBA_KP WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x6900.set Station VLBA_OV WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x6900.set Station VLBA_BR WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x6900.set Station VLBA_MK WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x7900.set Station VLBA_PT WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v4cm_3 1 1 T F T T T T T T v4cm_3 2 1 T F T T T T T T v4cm_3 3 1 T F T T T T F T v4cm_3 4 1 T F T T T T F T v4cm_3 5 1 T F T T T T F T v4cm_3 6 1 T F T T T T F T v4cm_3 7 1 T F T T T T F T v4cm_3 8 1 T F T T T T F T v4cm_4 1 1 T F T T T T T T v4cm_4 2 1 T F T T T T T T v4cm_4 3 1 T F T T T T T T v4cm_4 4 1 T F T T T T T T v4cm_4 5 1 T F T T T T T T v4cm_4 6 1 T F T T T T T T v4cm_4 7 1 T F T T T T T T v4cm_4 8 1 T F T T T T T T v4cm_5 1 1 T F T T T T F T v4cm_5 2 1 T F T T T T F T v4cm_5 3 1 T F T T T T T T v4cm_5 4 1 T F T T T T T T v4cm_5 5 1 T F T T T T T T v4cm_5 6 1 T F T T T T T T v4cm_5 7 1 T F T T T T T T v4cm_5 8 1 T F T T T T T T vsx_12 1 3 T F T T T T T T vsx_12 2 3 T F T T T T T T vsx_12 3 3 T F T T T T F T vsx_12 4 3 T F T T T T F T vsx_12 5 3 T F T T T T F T vsx_12 6 3 T F T T T T F T vsx_12 7 3 T F T T T T F T vsx_12 8 3 T F T T T T F T vsx_13 1 3 T F T T T T T T vsx_13 2 3 T F T T T T T T vsx_13 3 3 T F T T T T T T vsx_13 4 3 T F T T T T T T vsx_13 5 3 T F T T T T T T vsx_13 6 3 T F T T T T T T vsx_13 7 3 T F T T T T T T vsx_13 8 3 T F T T T T T T vsx_14 1 3 T F T T T T F T vsx_14 2 3 T F T T T T F T vsx_14 3 3 T F T T T T T T vsx_14 4 3 T F T T T T T T vsx_14 5 3 T F T T T T T T vsx_14 6 3 T F T T T T T T vsx_14 7 3 T F T T T T T T vsx_14 8 3 T F T T T T T T vsx_22 1 3 T F T T T T T T vsx_22 2 3 T F T T T T T T vsx_22 3 3 T F T T T T F T vsx_22 4 3 T F T T T T F T vsx_22 5 3 T F T T T T F T vsx_22 6 3 T F T T T T F T vsx_22 7 3 T F T T T T F T vsx_22 8 3 T F T T T T F T vsx_23 1 3 T F T T T T T T vsx_23 2 3 T F T T T T T T vsx_23 3 3 T F T T T T T T vsx_23 4 3 T F T T T T T T vsx_23 5 3 T F T T T T T T vsx_23 6 3 T F T T T T T T vsx_23 7 3 T F T T T T T T vsx_23 8 3 T F T T T T T T vsx_24 1 3 T F T T T T F T vsx_24 2 3 T F T T T T F T vsx_24 3 3 T F T T T T T T vsx_24 4 3 T F T T T T T T vsx_24 5 3 T F T T T T T T vsx_24 6 3 T F T T T T T T vsx_24 7 3 T F T T T T T T vsx_24 8 3 T F T T T T T T vsx_1w 1 3 T F T T T T F T vsx_1w 2 3 T F T T T T F T vsx_1w 3 3 T F T T T T F T vsx_1w 4 3 T F T T T T F T vsx_1w 5 3 T F T T T T F T vsx_1w 6 3 T F T T T T F T vsx_1w 7 3 T F T T T T F T vsx_1w 8 3 T F T T T T F T vsx_2w 1 3 T F T T T T T T vsx_2w 2 3 T F T T T T T T vsx_2w 3 3 T F T T T T F T vsx_2w 4 3 T F T T T T F T vsx_2w 5 3 T F T T T T F T vsx_2w 6 3 T F T T T T F T vsx_2w 7 3 T F T T T T F T vsx_2w 8 3 T F T T T T F T vsx_3w 1 3 T F T T T T F T vsx_3w 2 3 T F T T T T F T vsx_3w 3 3 T F T T T T F T vsx_3w 4 3 T F T T T T F T vsx_3w 5 3 T F T T T T F T vsx_3w 6 3 T F T T T T F T vsx_3w 7 3 T F T T T T F T vsx_3w 8 3 T F T T T T F T vsx_4w 1 3 T F T T T T T T vsx_4w 2 3 T F T T T T T T vsx_4w 3 3 T F T T T T F T vsx_4w 4 3 T F T T T T F T vsx_4w 5 3 T F T T T T F T vsx_4w 6 3 T F T T T T F T vsx_4w 7 3 T F T T T T F T vsx_4w 8 3 T F T T T T F T vsx_5w 1 3 T F T T T T F T vsx_5w 2 3 T F T T T T F T vsx_5w 3 3 T F T T T T F T vsx_5w 4 3 T F T T T T F T vsx_5w 5 3 T F T T T T F T vsx_5w 6 3 T F T T T T F T vsx_5w 7 3 T F T T T T F T vsx_5w 8 3 T F T T T T F T vsx_6w 1 3 T F T T T T T T vsx_6w 2 3 T F T T T T T T vsx_6w 3 3 T F T T T T F T vsx_6w 4 3 T F T T T T F T vsx_6w 5 3 T F T T T T F T vsx_6w 6 3 T F T T T T F T vsx_6w 7 3 T F T T T T F T vsx_6w 8 3 T F T T T T F T vsx_7w 1 3 T F T T T T F T vsx_7w 2 3 T F T T T T F T vsx_7w 3 3 T F T T T T F T vsx_7w 4 3 T F T T T T F T vsx_7w 5 3 T F T T T T F T vsx_7w 6 3 T F T T T T F T vsx_7w 7 3 T F T T T T F T vsx_7w 8 3 T F T T T T F T vsx_8w 1 3 T F T T T T T T vsx_8w 2 3 T F T T T T T T vsx_8w 3 3 T F T T T T F T vsx_8w 4 3 T F T T T T F T vsx_8w 5 3 T F T T T T F T vsx_8w 6 3 T F T T T T F T vsx_8w 7 3 T F T T T T F T vsx_8w 8 3 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x7900.set Station VLBA_KP WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v4cm_3 1 1 T F T T T T T T v4cm_3 2 1 T F T T T T T T v4cm_3 3 1 T F T T T T F T v4cm_3 4 1 T F T T T T F T v4cm_3 5 1 T F T T T T F T v4cm_3 6 1 T F T T T T F T v4cm_3 7 1 T F T T T T F T v4cm_3 8 1 T F T T T T F T v4cm_4 1 1 T F T T T T T T v4cm_4 2 1 T F T T T T T T v4cm_4 3 1 T F T T T T T T v4cm_4 4 1 T F T T T T T T v4cm_4 5 1 T F T T T T T T v4cm_4 6 1 T F T T T T T T v4cm_4 7 1 T F T T T T T T v4cm_4 8 1 T F T T T T T T v4cm_5 1 1 T F T T T T F T v4cm_5 2 1 T F T T T T F T v4cm_5 3 1 T F T T T T T T v4cm_5 4 1 T F T T T T T T v4cm_5 5 1 T F T T T T T T v4cm_5 6 1 T F T T T T T T v4cm_5 7 1 T F T T T T T T v4cm_5 8 1 T F T T T T T T vsx_12 1 3 T F T T T T T T vsx_12 2 3 T F T T T T T T vsx_12 3 3 T F T T T T F T vsx_12 4 3 T F T T T T F T vsx_12 5 3 T F T T T T F T vsx_12 6 3 T F T T T T F T vsx_12 7 3 T F T T T T F T vsx_12 8 3 T F T T T T F T vsx_13 1 3 T F T T T T T T vsx_13 2 3 T F T T T T T T vsx_13 3 3 T F T T T T T T vsx_13 4 3 T F T T T T T T vsx_13 5 3 T F T T T T T T vsx_13 6 3 T F T T T T T T vsx_13 7 3 T F T T T T T T vsx_13 8 3 T F T T T T T T vsx_14 1 3 T F T T T T F T vsx_14 2 3 T F T T T T F T vsx_14 3 3 T F T T T T T T vsx_14 4 3 T F T T T T T T vsx_14 5 3 T F T T T T T T vsx_14 6 3 T F T T T T T T vsx_14 7 3 T F T T T T T T vsx_14 8 3 T F T T T T T T vsx_22 1 3 T F T T T T T T vsx_22 2 3 T F T T T T T T vsx_22 3 3 T F T T T T F T vsx_22 4 3 T F T T T T F T vsx_22 5 3 T F T T T T F T vsx_22 6 3 T F T T T T F T vsx_22 7 3 T F T T T T F T vsx_22 8 3 T F T T T T F T vsx_23 1 3 T F T T T T T T vsx_23 2 3 T F T T T T T T vsx_23 3 3 T F T T T T T T vsx_23 4 3 T F T T T T T T vsx_23 5 3 T F T T T T T T vsx_23 6 3 T F T T T T T T vsx_23 7 3 T F T T T T T T vsx_23 8 3 T F T T T T T T vsx_24 1 3 T F T T T T F T vsx_24 2 3 T F T T T T F T vsx_24 3 3 T F T T T T T T vsx_24 4 3 T F T T T T T T vsx_24 5 3 T F T T T T T T vsx_24 6 3 T F T T T T T T vsx_24 7 3 T F T T T T T T vsx_24 8 3 T F T T T T T T vsx_1w 1 3 T F T T T T F T vsx_1w 2 3 T F T T T T F T vsx_1w 3 3 T F T T T T F T vsx_1w 4 3 T F T T T T F T vsx_1w 5 3 T F T T T T F T vsx_1w 6 3 T F T T T T F T vsx_1w 7 3 T F T T T T F T vsx_1w 8 3 T F T T T T F T vsx_2w 1 3 T F T T T T T T vsx_2w 2 3 T F T T T T T T vsx_2w 3 3 T F T T T T F T vsx_2w 4 3 T F T T T T F T vsx_2w 5 3 T F T T T T F T vsx_2w 6 3 T F T T T T F T vsx_2w 7 3 T F T T T T F T vsx_2w 8 3 T F T T T T F T vsx_3w 1 3 T F T T T T F T vsx_3w 2 3 T F T T T T F T vsx_3w 3 3 T F T T T T F T vsx_3w 4 3 T F T T T T F T vsx_3w 5 3 T F T T T T F T vsx_3w 6 3 T F T T T T F T vsx_3w 7 3 T F T T T T F T vsx_3w 8 3 T F T T T T F T vsx_4w 1 3 T F T T T T T T vsx_4w 2 3 T F T T T T T T vsx_4w 3 3 T F T T T T F T vsx_4w 4 3 T F T T T T F T vsx_4w 5 3 T F T T T T F T vsx_4w 6 3 T F T T T T F T vsx_4w 7 3 T F T T T T F T vsx_4w 8 3 T F T T T T F T vsx_5w 1 3 T F T T T T F T vsx_5w 2 3 T F T T T T F T vsx_5w 3 3 T F T T T T F T vsx_5w 4 3 T F T T T T F T vsx_5w 5 3 T F T T T T F T vsx_5w 6 3 T F T T T T F T vsx_5w 7 3 T F T T T T F T vsx_5w 8 3 T F T T T T F T vsx_6w 1 3 T F T T T T T T vsx_6w 2 3 T F T T T T T T vsx_6w 3 3 T F T T T T F T vsx_6w 4 3 T F T T T T F T vsx_6w 5 3 T F T T T T F T vsx_6w 6 3 T F T T T T F T vsx_6w 7 3 T F T T T T F T vsx_6w 8 3 T F T T T T F T vsx_7w 1 3 T F T T T T F T vsx_7w 2 3 T F T T T T F T vsx_7w 3 3 T F T T T T F T vsx_7w 4 3 T F T T T T F T vsx_7w 5 3 T F T T T T F T vsx_7w 6 3 T F T T T T F T vsx_7w 7 3 T F T T T T F T vsx_7w 8 3 T F T T T T F T vsx_8w 1 3 T F T T T T T T vsx_8w 2 3 T F T T T T T T vsx_8w 3 3 T F T T T T F T vsx_8w 4 3 T F T T T T F T vsx_8w 5 3 T F T T T T F T vsx_8w 6 3 T F T T T T F T vsx_8w 7 3 T F T T T T F T vsx_8w 8 3 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x7900.set Station VLBA_OV WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v4cm_3 1 1 T F T T T T T T v4cm_3 2 1 T F T T T T T T v4cm_3 3 1 T F T T T T F T v4cm_3 4 1 T F T T T T F T v4cm_3 5 1 T F T T T T F T v4cm_3 6 1 T F T T T T F T v4cm_3 7 1 T F T T T T F T v4cm_3 8 1 T F T T T T F T v4cm_4 1 1 T F T T T T T T v4cm_4 2 1 T F T T T T T T v4cm_4 3 1 T F T T T T T T v4cm_4 4 1 T F T T T T T T v4cm_4 5 1 T F T T T T T T v4cm_4 6 1 T F T T T T T T v4cm_4 7 1 T F T T T T T T v4cm_4 8 1 T F T T T T T T v4cm_5 1 1 T F T T T T F T v4cm_5 2 1 T F T T T T F T v4cm_5 3 1 T F T T T T T T v4cm_5 4 1 T F T T T T T T v4cm_5 5 1 T F T T T T T T v4cm_5 6 1 T F T T T T T T v4cm_5 7 1 T F T T T T T T v4cm_5 8 1 T F T T T T T T vsx_12 1 3 T F T T T T T T vsx_12 2 3 T F T T T T T T vsx_12 3 3 T F T T T T F T vsx_12 4 3 T F T T T T F T vsx_12 5 3 T F T T T T F T vsx_12 6 3 T F T T T T F T vsx_12 7 3 T F T T T T F T vsx_12 8 3 T F T T T T F T vsx_13 1 3 T F T T T T T T vsx_13 2 3 T F T T T T T T vsx_13 3 3 T F T T T T T T vsx_13 4 3 T F T T T T T T vsx_13 5 3 T F T T T T T T vsx_13 6 3 T F T T T T T T vsx_13 7 3 T F T T T T T T vsx_13 8 3 T F T T T T T T vsx_14 1 3 T F T T T T F T vsx_14 2 3 T F T T T T F T vsx_14 3 3 T F T T T T T T vsx_14 4 3 T F T T T T T T vsx_14 5 3 T F T T T T T T vsx_14 6 3 T F T T T T T T vsx_14 7 3 T F T T T T T T vsx_14 8 3 T F T T T T T T vsx_22 1 3 T F T T T T T T vsx_22 2 3 T F T T T T T T vsx_22 3 3 T F T T T T F T vsx_22 4 3 T F T T T T F T vsx_22 5 3 T F T T T T F T vsx_22 6 3 T F T T T T F T vsx_22 7 3 T F T T T T F T vsx_22 8 3 T F T T T T F T vsx_23 1 3 T F T T T T T T vsx_23 2 3 T F T T T T T T vsx_23 3 3 T F T T T T T T vsx_23 4 3 T F T T T T T T vsx_23 5 3 T F T T T T T T vsx_23 6 3 T F T T T T T T vsx_23 7 3 T F T T T T T T vsx_23 8 3 T F T T T T T T vsx_24 1 3 T F T T T T F T vsx_24 2 3 T F T T T T F T vsx_24 3 3 T F T T T T T T vsx_24 4 3 T F T T T T T T vsx_24 5 3 T F T T T T T T vsx_24 6 3 T F T T T T T T vsx_24 7 3 T F T T T T T T vsx_24 8 3 T F T T T T T T vsx_1w 1 3 T F T T T T F T vsx_1w 2 3 T F T T T T F T vsx_1w 3 3 T F T T T T F T vsx_1w 4 3 T F T T T T F T vsx_1w 5 3 T F T T T T F T vsx_1w 6 3 T F T T T T F T vsx_1w 7 3 T F T T T T F T vsx_1w 8 3 T F T T T T F T vsx_2w 1 3 T F T T T T T T vsx_2w 2 3 T F T T T T T T vsx_2w 3 3 T F T T T T F T vsx_2w 4 3 T F T T T T F T vsx_2w 5 3 T F T T T T F T vsx_2w 6 3 T F T T T T F T vsx_2w 7 3 T F T T T T F T vsx_2w 8 3 T F T T T T F T vsx_3w 1 3 T F T T T T F T vsx_3w 2 3 T F T T T T F T vsx_3w 3 3 T F T T T T F T vsx_3w 4 3 T F T T T T F T vsx_3w 5 3 T F T T T T F T vsx_3w 6 3 T F T T T T F T vsx_3w 7 3 T F T T T T F T vsx_3w 8 3 T F T T T T F T vsx_4w 1 3 T F T T T T T T vsx_4w 2 3 T F T T T T T T vsx_4w 3 3 T F T T T T F T vsx_4w 4 3 T F T T T T F T vsx_4w 5 3 T F T T T T F T vsx_4w 6 3 T F T T T T F T vsx_4w 7 3 T F T T T T F T vsx_4w 8 3 T F T T T T F T vsx_5w 1 3 T F T T T T F T vsx_5w 2 3 T F T T T T F T vsx_5w 3 3 T F T T T T F T vsx_5w 4 3 T F T T T T F T vsx_5w 5 3 T F T T T T F T vsx_5w 6 3 T F T T T T F T vsx_5w 7 3 T F T T T T F T vsx_5w 8 3 T F T T T T F T vsx_6w 1 3 T F T T T T T T vsx_6w 2 3 T F T T T T T T vsx_6w 3 3 T F T T T T F T vsx_6w 4 3 T F T T T T F T vsx_6w 5 3 T F T T T T F T vsx_6w 6 3 T F T T T T F T vsx_6w 7 3 T F T T T T F T vsx_6w 8 3 T F T T T T F T vsx_7w 1 3 T F T T T T F T vsx_7w 2 3 T F T T T T F T vsx_7w 3 3 T F T T T T F T vsx_7w 4 3 T F T T T T F T vsx_7w 5 3 T F T T T T F T vsx_7w 6 3 T F T T T T F T vsx_7w 7 3 T F T T T T F T vsx_7w 8 3 T F T T T T F T vsx_8w 1 3 T F T T T T T T vsx_8w 2 3 T F T T T T T T vsx_8w 3 3 T F T T T T F T vsx_8w 4 3 T F T T T T F T vsx_8w 5 3 T F T T T T F T vsx_8w 6 3 T F T T T T F T vsx_8w 7 3 T F T T T T F T vsx_8w 8 3 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x7900.set Station VLBA_BR WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v4cm_3 1 1 T F T T T T T T v4cm_3 2 1 T F T T T T T T v4cm_3 3 1 T F T T T T F T v4cm_3 4 1 T F T T T T F T v4cm_3 5 1 T F T T T T F T v4cm_3 6 1 T F T T T T F T v4cm_3 7 1 T F T T T T F T v4cm_3 8 1 T F T T T T F T v4cm_4 1 1 T F T T T T T T v4cm_4 2 1 T F T T T T T T v4cm_4 3 1 T F T T T T T T v4cm_4 4 1 T F T T T T T T v4cm_4 5 1 T F T T T T T T v4cm_4 6 1 T F T T T T T T v4cm_4 7 1 T F T T T T T T v4cm_4 8 1 T F T T T T T T v4cm_5 1 1 T F T T T T F T v4cm_5 2 1 T F T T T T F T v4cm_5 3 1 T F T T T T T T v4cm_5 4 1 T F T T T T T T v4cm_5 5 1 T F T T T T T T v4cm_5 6 1 T F T T T T T T v4cm_5 7 1 T F T T T T T T v4cm_5 8 1 T F T T T T T T vsx_12 1 3 T F T T T T T T vsx_12 2 3 T F T T T T T T vsx_12 3 3 T F T T T T F T vsx_12 4 3 T F T T T T F T vsx_12 5 3 T F T T T T F T vsx_12 6 3 T F T T T T F T vsx_12 7 3 T F T T T T F T vsx_12 8 3 T F T T T T F T vsx_13 1 3 T F T T T T T T vsx_13 2 3 T F T T T T T T vsx_13 3 3 T F T T T T T T vsx_13 4 3 T F T T T T T T vsx_13 5 3 T F T T T T T T vsx_13 6 3 T F T T T T T T vsx_13 7 3 T F T T T T T T vsx_13 8 3 T F T T T T T T vsx_14 1 3 T F T T T T F T vsx_14 2 3 T F T T T T F T vsx_14 3 3 T F T T T T T T vsx_14 4 3 T F T T T T T T vsx_14 5 3 T F T T T T T T vsx_14 6 3 T F T T T T T T vsx_14 7 3 T F T T T T T T vsx_14 8 3 T F T T T T T T vsx_22 1 3 T F T T T T T T vsx_22 2 3 T F T T T T T T vsx_22 3 3 T F T T T T F T vsx_22 4 3 T F T T T T F T vsx_22 5 3 T F T T T T F T vsx_22 6 3 T F T T T T F T vsx_22 7 3 T F T T T T F T vsx_22 8 3 T F T T T T F T vsx_23 1 3 T F T T T T T T vsx_23 2 3 T F T T T T T T vsx_23 3 3 T F T T T T T T vsx_23 4 3 T F T T T T T T vsx_23 5 3 T F T T T T T T vsx_23 6 3 T F T T T T T T vsx_23 7 3 T F T T T T T T vsx_23 8 3 T F T T T T T T vsx_24 1 3 T F T T T T F T vsx_24 2 3 T F T T T T F T vsx_24 3 3 T F T T T T T T vsx_24 4 3 T F T T T T T T vsx_24 5 3 T F T T T T T T vsx_24 6 3 T F T T T T T T vsx_24 7 3 T F T T T T T T vsx_24 8 3 T F T T T T T T vsx_1w 1 3 T F T T T T F T vsx_1w 2 3 T F T T T T F T vsx_1w 3 3 T F T T T T F T vsx_1w 4 3 T F T T T T F T vsx_1w 5 3 T F T T T T F T vsx_1w 6 3 T F T T T T F T vsx_1w 7 3 T F T T T T F T vsx_1w 8 3 T F T T T T F T vsx_2w 1 3 T F T T T T T T vsx_2w 2 3 T F T T T T T T vsx_2w 3 3 T F T T T T F T vsx_2w 4 3 T F T T T T F T vsx_2w 5 3 T F T T T T F T vsx_2w 6 3 T F T T T T F T vsx_2w 7 3 T F T T T T F T vsx_2w 8 3 T F T T T T F T vsx_3w 1 3 T F T T T T F T vsx_3w 2 3 T F T T T T F T vsx_3w 3 3 T F T T T T F T vsx_3w 4 3 T F T T T T F T vsx_3w 5 3 T F T T T T F T vsx_3w 6 3 T F T T T T F T vsx_3w 7 3 T F T T T T F T vsx_3w 8 3 T F T T T T F T vsx_4w 1 3 T F T T T T T T vsx_4w 2 3 T F T T T T T T vsx_4w 3 3 T F T T T T F T vsx_4w 4 3 T F T T T T F T vsx_4w 5 3 T F T T T T F T vsx_4w 6 3 T F T T T T F T vsx_4w 7 3 T F T T T T F T vsx_4w 8 3 T F T T T T F T vsx_5w 1 3 T F T T T T F T vsx_5w 2 3 T F T T T T F T vsx_5w 3 3 T F T T T T F T vsx_5w 4 3 T F T T T T F T vsx_5w 5 3 T F T T T T F T vsx_5w 6 3 T F T T T T F T vsx_5w 7 3 T F T T T T F T vsx_5w 8 3 T F T T T T F T vsx_6w 1 3 T F T T T T T T vsx_6w 2 3 T F T T T T T T vsx_6w 3 3 T F T T T T F T vsx_6w 4 3 T F T T T T F T vsx_6w 5 3 T F T T T T F T vsx_6w 6 3 T F T T T T F T vsx_6w 7 3 T F T T T T F T vsx_6w 8 3 T F T T T T F T vsx_7w 1 3 T F T T T T F T vsx_7w 2 3 T F T T T T F T vsx_7w 3 3 T F T T T T F T vsx_7w 4 3 T F T T T T F T vsx_7w 5 3 T F T T T T F T vsx_7w 6 3 T F T T T T F T vsx_7w 7 3 T F T T T T F T vsx_7w 8 3 T F T T T T F T vsx_8w 1 3 T F T T T T T T vsx_8w 2 3 T F T T T T T T vsx_8w 3 3 T F T T T T F T vsx_8w 4 3 T F T T T T F T vsx_8w 5 3 T F T T T T F T vsx_8w 6 3 T F T T T T F T vsx_8w 7 3 T F T T T T F T vsx_8w 8 3 T F T T T T F T Unless this is 3mm, since this is the VLBA, it is very likely that there is an error in the setup. --------------------------------------- SETFCAT: In setup: /home/aakash/kudre/VLBA/rfitest/x7900.set Station VLBA_MK WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band v4cm_3 1 1 T F T T T T T T v4cm_3 2 1 T F T T T T T T v4cm_3 3 1 T F T T T T F T v4cm_3 4 1 T F T T T T F T v4cm_3 5 1 T F T T T T F T v4cm_3 6 1 T F T T T T F T v4cm_3 7 1 T F T T T T F T v4cm_3 8 1 T F T T T T F T v4cm_4 1 1 T F T T T T T T v4cm_4 2 1 T F T T T T T T v4cm_4 3 1 T F T T T T T T v4cm_4 4 1 T F T T T T T T v4cm_4 5 1 T F T T T T T T v4cm_4 6 1 T F T T T T T T v4cm_4 7 1 T F T T T T T T v4cm_4 8 1 T F T T T T T T v4cm_5 1 1 T F T T T T F T v4cm_5 2 1 T F T T T T F T v4cm_5 3 1 T F T T T T T T v4cm_5 4 1 T F T T T T T T v4cm_5 5 1 T F T T T T T T v4cm_5 6 1 T F T T T T T T v4cm_5 7 1 T F T T T T T T v4cm_5 8 1 T F T T T T T T vsx_12 1 3 T F T T T T T T vsx_12 2 3 T F T T T T T T vsx_12 3 3 T F T T T T F T vsx_12 4 3 T F T T T T F T vsx_12 5 3 T F T T T T F T vsx_12 6 3 T F T T T T F T vsx_12 7 3 T F T T T T F T vsx_12 8 3 T F T T T T F T vsx_13 1 3 T F T T T T T T vsx_13 2 3 T F T T T T T T vsx_13 3 3 T F T T T T T T vsx_13 4 3 T F T T T T T T vsx_13 5 3 T F T T T T T T vsx_13 6 3 T F T T T T T T vsx_13 7 3 T F T T T T T T vsx_13 8 3 T F T T T T T T vsx_14 1 3 T F T T T T F T vsx_14 2 3 T F T T T T F T vsx_14 3 3 T F T T T T T T vsx_14 4 3 T F T T T T T T vsx_14 5 3 T F T T T T T T vsx_14 6 3 T F T T T T T T vsx_14 7 3 T F T T T T T T vsx_14 8 3 T F T T T T T T vsx_22 1 3 T F T T T T T T vsx_22 2 3 T F T T T T T T vsx_22 3 3 T F T T T T F T vsx_22 4 3 T F T T T T F T vsx_22 5 3 T F T T T T F T vsx_22 6 3 T F T T T T F T vsx_22 7 3 T F T T T T F T vsx_22 8 3 T F T T T T F T vsx_23 1 3 T F T T T T T T vsx_23 2 3 T F T T T T T T vsx_23 3 3 T F T T T T T T vsx_23 4 3 T F T T T T T T vsx_23 5 3 T F T T T T T T vsx_23 6 3 T F T T T T T T vsx_23 7 3 T F T T T T T T vsx_23 8 3 T F T T T T T T vsx_24 1 3 T F T T T T F T vsx_24 2 3 T F T T T T F T vsx_24 3 3 T F T T T T T T vsx_24 4 3 T F T T T T T T vsx_24 5 3 T F T T T T T T vsx_24 6 3 T F T T T T T T vsx_24 7 3 T F T T T T T T vsx_24 8 3 T F T T T T T T vsx_1w 1 3 T F T T T T F T vsx_1w 2 3 T F T T T T F T vsx_1w 3 3 T F T T T T F T vsx_1w 4 3 T F T T T T F T vsx_1w 5 3 T F T T T T F T vsx_1w 6 3 T F T T T T F T vsx_1w 7 3 T F T T T T F T vsx_1w 8 3 T F T T T T F T vsx_2w 1 3 T F T T T T T T vsx_2w 2 3 T F T T T T T T vsx_2w 3 3 T F T T T T F T vsx_2w 4 3 T F T T T T F T vsx_2w 5 3 T F T T T T F T vsx_2w 6 3 T F T T T T F T vsx_2w 7 3 T F T T T T F T vsx_2w 8 3 T F T T T T F T vsx_3w 1 3 T F T T T T F T vsx_3w 2 3 T F T T T T F T vsx_3w 3 3 T F T T T T F T vsx_3w 4 3 T F T T T T F T vsx_3w 5 3 T F T T T T F T vsx_3w 6 3 T F T T T T F T vsx_3w 7 3 T F T T T T F T vsx_3w 8 3 T F T T T T F T vsx_4w 1 3 T F T T T T T T vsx_4w 2 3 T F T T T T T T vsx_4w 3 3 T F T T T T F T vsx_4w 4 3 T F T T T T F T vsx_4w 5 3 T F T T T T F T vsx_4w 6 3 T F T T T T F T vsx_4w 7 3 T F T T T T F T vsx_4w 8 3 T F T T T T F T vsx_5w 1 3 T F T T T T F T vsx_5w 2 3 T F T T T T F T vsx_5w 3 3 T F T T T T F T vsx_5w 4 3 T F T T T T F T vsx_5w 5 3 T F T T T T F T vsx_5w 6 3 T F T T T T F T vsx_5w 7 3 T F T T T T F T vsx_5w 8 3 T F T T T T F T vsx_6w 1 3 T F T T T T T T vsx_6w 2 3 T F T T T T T T vsx_6w 3 3 T F T T T T F T vsx_6w 4 3 T F T T T T F T vsx_6w