COVER INFORMATION Station: VLBA_HN (Code Hn ) Experiment: VLBA Monitoring Exp. Code: MT416 Schedule Version: 3.10 Processed by SCHED version: Release of 18 Sept. 2003 PI: Lorant Sjouwerman Address: NRAO-AOC P.O.Box O Socorro NM 87801, U.S.A. Phone: +1-505-838-4507 (home) EMAIL: lsjouwer@nrao.edu, analysts@nrao.edu Fax: Phone during observation: +1-505-835-7332 (work) Observing mode: VLBA 128MHz 8bbc 1bit R+L Notes: VLBA Monitoring test in dynamic scheduling and runs for 90 minutes (1.5 hours) total. Note: MAKE SURE ONE SOURCE IS SELECTED COVER LETTER: Please schedule ONE source depending on between approximately -3h to +3h of LST in Pie Town; a source can be selected by deleting the -one and only- ONE explanation mark in front of it. Schedule for VLBA_HN (Code Hn ) Page 2 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 21 Apr 2004 Day 112 --- Next scan frequencies: 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 Next BBC frequencies: 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Next scan bandwidths: 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 05 58 52 1253-055 15 09 32 32.7 220.4 2.2 28.5 0 1 1 0 05 58 52 06 05 21 --- 15 16 02 31.9 222.1 2.3 29.6 389 F 1 5186 Next scan frequencies: 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 Next BBC frequencies: 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 06 07 21 1253-055 15 18 02 31.6 222.6 2.4 29.9 114 1 1 5186 06 07 21 06 13 50 --- 15 24 32 30.8 224.2 2.5 30.9 389 F 1 10372 Next scan frequencies: 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 Next BBC frequencies: 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 06 14 50 1253-055 15 25 32 30.7 224.5 2.5 31.0 54 1 1 10372 06 14 50 06 21 19 --- 15 32 02 29.9 226.1 2.6 32.0 389 F 1 15557 Next scan frequencies: 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 Next BBC frequencies: 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 06 23 18 1253-055 15 34 02 29.6 226.6 2.6 32.3 114 1 2 15557 06 23 18 06 29 47 --- 15 40 32 28.7 228.1 2.7 33.2 389 R 1 14457 Next scan frequencies: 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 Next BBC frequencies: 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 06 30 47 1253-055 15 41 32 28.6 228.4 2.8 33.4 54 1 2 14457 06 30 47 06 37 16 --- 15 48 02 27.7 229.9 2.9 34.3 389 R 1 9271 Schedule for VLBA_HN (Code Hn ) Page 3 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 21 Apr 2004 Day 112 --- Next scan frequencies: 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 Next BBC frequencies: 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 06 39 16 1253-055 15 50 02 27.4 230.4 2.9 34.5 114 1 2 9271 06 39 16 06 45 45 --- 15 56 32 26.5 231.8 3.0 35.4 389 R 1 4085 Next scan frequencies: 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 Next BBC frequencies: 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 06 46 44 1253-055 15 57 32 26.3 232.1 3.0 35.5 54 1 1 4085 06 46 44 06 53 13 --- 16 04 02 25.4 233.5 3.1 36.3 389 F 2 1101 Next scan frequencies: 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 Next BBC frequencies: 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 06 55 13 1253-055 16 06 02 25.1 234.0 3.2 36.5 113 1 1 1101 06 55 13 07 01 42 --- 16 12 32 24.1 235.4 3.3 37.3 389 F 2 6286 Next scan frequencies: 4974.49 4974.49 4990.49 4990.49 Next BBC frequencies: 874.49 874.49 890.49 890.49 Next scan bandwidths: 16.00 16.00 16.00 16.00 07 03 42 1253-055 16 14 32 23.8 235.8 3.3 37.5 113 1 1 6286 07 03 42 07 10 11 --- 16 21 02 22.8 237.2 3.4 38.2 389 F 2 11472 Next scan frequencies: 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 Next BBC frequencies: 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Next scan bandwidths: 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 07 11 10 1253-055 16 22 02 22.7 237.4 3.4 38.3 54 1 1 11472 07 11 10 07 17 39 --- 16 28 32 21.7 238.8 3.5 39.0 389 F 2 16658 Schedule for VLBA_HN (Code Hn ) Page 4 VLBA Monitoring UP: D => Below limits; H => Below horizon mask. blank => Up. Early: Seconds between end of slew and start. Dwell: On source seconds. Tapes: Drive, Index, Start footage / Direction, Head Group, End footage. TPStart: Tape motion start time. Frequencies are LO sum (band edge). Automatic tape allocation specified. Tape positions are just estimates. ---------------------------------------------------------------------------------------- Start UT Source Start / Stop Early Tapes TPStart Stop UT LST EL AZ HA UP ParA Dwell (see above) ---------------------------------------------------------------------------------------- --- Wed 21 Apr 2004 Day 112 --- Next scan frequencies: 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 Next BBC frequencies: 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 07 20 39 1253-055 16 31 32 21.2 239.4 3.6 39.3 173 1 2 16658 07 20 39 07 28 38 --- 16 39 32 19.9 241.0 3.7 40.1 479 R 2 12159 SETUP FILE INFORMATION: NOTE: If DOPPLER, FREQ, or BW were used, see the individual scans for the final BBC settings. Setup file: band.21cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 1 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 1 Setup file default. Used pcal sets: 1 LO sum= 1400.49 1400.49 1408.49 1408.49 1416.49 1416.49 1424.49 1424.49 BBC fr= 999.51 999.51 991.51 991.51 983.51 983.51 975.51 975.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.18cm Matches group v20cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat FD filtered above 1760. SC filtered above 1740. Setup group: 2 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 2400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 20cm omit 20cm omit VLBA Synth= 15.4 2.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 2 Setup file default. Used pcal sets: 1 LO sum= 1642.49 1642.49 1650.49 1650.49 1658.49 1658.49 1666.49 1666.49 BBC fr= 757.51 757.51 749.51 749.51 741.51 741.51 733.51 733.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.13cm Matches group v13cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat LA,NL only 2200-2400 Setup group: 3 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 3100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= L L L L L L L L IF = A C A C A C A C VLBA FE= 13cm omit 13cm omit VLBA Synth= 15.4 3.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 3 Setup file default. Used pcal sets: 1 LO sum= 2279.49 2279.49 2287.49 2287.49 2295.49 2295.49 2303.49 2303.49 BBC fr= 820.51 820.51 812.51 812.51 804.51 804.51 796.51 796.51 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.6cm Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 4 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 4 Setup file default. Used pcal sets: 1 LO sum= 4974.49 4974.49 4982.49 4982.49 4990.49 4990.49 4998.49 4998.49 BBC fr= 874.49 874.49 882.49 882.49 890.49 890.49 898.49 898.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 Setup file: band.4cm Matches group v4cm_3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 5 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 7600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 4cm omit 4cm VLBA Synth= 7.6 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 5 Setup file default. Used pcal sets: 1 LO sum= 8399.49 8399.49 8407.49 8407.49 8415.49 8415.49 8423.49 8423.49 BBC fr= 799.49 799.49 807.49 807.49 815.49 815.49 823.49 823.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.2cm Matches group v2cm_d3 in /home/filehost/cwalker/sched/catalogs/freq.dat Fourth 2cm filter Setup group: 6 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 14600.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 2cm omit 2cm VLBA Synth= 14.6 10.9 10.9 The following frequency sets based on this setup were used. Frequency Set: 6 Setup file default. Used pcal sets: 1 LO sum= 15269.49 15269.49 15277.49 15277.49 15285.49 15285.49 15293.49 15293.49 BBC fr= 669.49 669.49 677.49 677.49 685.49 685.49 693.49 693.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_auto Setup file: band.1cm Matches group v1cm_b3 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 7 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 21500.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 1cm omit 1cm VLBA Synth= 9.1 15.4 12.4 The following frequency sets based on this setup were used. Frequency Set: 7 Setup file default. Used pcal sets: 1 LO sum= 22219.49 22219.49 22227.49 22227.49 22235.49 22235.49 22243.49 22243.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 Setup file: band.7mm Matches group v7mm_c8 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 8 Station: VLBA Total bit rate: 128 Format: VLBA1:2 Bits per sample: 1 Sample rate: 16.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 42400.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 7mm omit 7mm omit VLBA Synth= 15.4 7.6 11.6 The following frequency sets based on this setup were used. Frequency Set: 8 Setup file default. Used pcal sets: 1 LO sum= 43119.49 43119.49 43127.49 43127.49 43135.49 43135.49 43143.49 43143.49 BBC fr= 719.49 719.49 727.49 727.49 735.49 735.49 743.49 743.49 Bandwd= 8.000 8.000 8.000 8.000 8.000 8.000 8.000 8.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 1 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 6510 6510 6510 6510 PCALFR2= 510 510 510 510 6510 6510 6510 6510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_8 Setup file: band.6-16 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 9 Station: VLBA Total bit rate: 128 Format: VLBA1:4 Bits per sample: 1 Sample rate: 32.000 Number of channels: 4 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U Pol. = RCP LCP RCP LCP BBC = 1 2 3 4 BBC SB= U U U U IF = A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 9 Setup file default. Used pcal sets: 2 LO sum= 4974.49 4974.49 4990.49 4990.49 BBC fr= 874.49 874.49 890.49 890.49 Bandwd= 16.000 16.000 16.000 16.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 2 PCAL = 1MHZ PCALXB1= S1 S3 S1 S3 S1 S3 S1 S3 PCALXB2= S2 S4 S2 S4 S2 S4 S2 S4 PCALFR1= 510 510 13510 13510 0 0 1510 1510 PCALFR2= 510 510 13510 13510 0 0 1510 1510 Track assignments are: track1= 2, 10, 18, 26 track2= 3, 11, 19, 27 barrel=roll_auto Setup file: band.6-4 Matches group v6cm_2 in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 10 Station: VLBA Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 4100.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = A C A C A C A C VLBA FE= 6cm omit 6cm omit VLBA Synth= 15.4 4.1 15.4 The following frequency sets based on this setup were used. Frequency Set: 10 Setup file default. Used pcal sets: 3 LO sum= 4982.49 4982.49 4986.49 4986.49 4990.49 4990.49 4994.49 4994.49 BBC fr= 882.49 882.49 886.49 886.49 890.49 890.49 894.49 894.49 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 3 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 510 510 510 510 2510 2510 2510 2510 PCALFR2= 510 510 510 510 2510 2510 2510 2510 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_off Setup file: band.9050 Matches group v5090n in /home/filehost/cwalker/sched/catalogs/freq.dat Setup group: 11 Station: VLBA Total bit rate: 128 Format: VLBA1:1 Bits per sample: 2 Sample rate: 8.000 Number of channels: 8 Passes/head pos: 2 Speedup factor: 1.00 Tape speeds: Low density - 266.660 ips, High density - 160.00 ips Time per pass for 17600 ft, High density tapes is: 00:22:00 1st LO= -500.00 -500.00 -500.00 -500.00 -500.00 -500.00 0.00 0.00 Net SB= U U U U U U U U Pol. = RCP LCP RCP LCP RCP LCP RCP LCP BBC = 1 2 3 4 5 6 7 8 BBC SB= U U U U U U U U IF = B D B D B D B D VLBA FE= omit 90cm omit 90cm VLBA Synth= 15.4 15.4 15.4 The following frequency sets based on this setup were used. Frequency Set: 11 Setup file default. Used pcal sets: 4 LO sum= 315.99 315.99 319.99 319.99 323.99 323.99 608.99 608.99 BBC fr= 815.99 815.99 819.99 819.99 823.99 823.99 608.99 608.99 Bandwd= 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4.000 The following pulse cal sets were used with this setup: Pulse cal detection set: 4 PCAL = 1MHZ PCALXB1= S1 S3 S5 S7 S1 S3 S5 S7 PCALXB2= S2 S4 S6 S8 S2 S4 S6 S8 PCALFR1= 10 10 10 10 3010 3010 3010 3010 PCALFR2= 10 10 10 10 3010 3010 3010 3010 Track assignments are: track1= 2, 6, 10, 14, 18, 22, 26, 30 track2= 3, 7, 11, 15, 19, 23, 27, 31 barrel=roll_16 SOURCE LIST -- VLBA Monitoring Catalog positions marked with *. Precession of date coordinates is based on stop time of first scan. Names used in schedule marked with *. Short names used in VLA and SNAP files marked with +. Observation date used in B1950/J2000 coordinate conversion (PRECDATE): 1979.900 No adjustments are made for rates (DRA, DDEC). Source Source position (RA/Dec) (B1950) (J2000) (Date) J1256-0547 12 53 35.831293 * 12 56 11.166560 12 56 24.937456 * 1253-055 -05 31 07.99572 *-05 47 21.52458 -05 48 49.66099 3C279 /home/filehost/cwalker/sched/catalogs/sources.vlba J1256-05 ICRF - Ext.1 Source - 1998 IERS Annual Report The solar corona can cause unstable phases for sources too close to the Sun. SCHED provides warnings at individual scans for distances less than 10 degrees. The distance from the Sun to each source in this schedule is: Source Sun distance (deg) 1253-055 163.7 Barry Clark estimates from predictions by Ketan Desai of IPM scattering sizes that the Sun will cause amplitude reductions on the longest VLBA baselines at a solar distance of 60deg F^(-0.6) where F is in GHz. For common VLBI bands, this is: 327 MHz 117. deg 610 MHz 81. deg 1.6 GHz 45. deg 2.3 GHz 36. deg 5.0 GHz 23. deg 8.4 GHz 17. deg 15.0 GHz 12. deg 22.0 GHz 9. deg 43.0 GHz 6. deg